Эта страница является переводом страницы HDL. Перевод выполнен на 98%.

Other languages:

English • ‎русский

Содержание

1 iRidium for HDL Buspro
2 Description
3 Connection
4 Devices
5 HDL CMD Test. Testing Sent Commands

iRidium for HDL Buspro

a set of tools for creating interfaces to control equipment in the HDL Buspro bus

The documentation was updated on 14.12.2023

training:
webinars and video-lessons >>

download:
Control of HDL Buspro, a set of projects

download:
Control of HDL Enviro

Description

iRidium for HDL Buspro is a set of tools for creating interfaces to control homes or offices on the basis of HDL equipment.

iRidium for HDL Buspro enables connection of control panels (iOS, Android, Windows, Mac) to the HDL bus via any HDL IP interface. At that the number of concurrent connections is not limited by the interface.

Connection

Equipment configuration and settings required for iRidium to control HDL equipment.

Ways of connection to HDL

Different ways of connection to the bus enable local work and work via the Internet, depending on whether you have a static IP-address or not :

1. Local

2. Internet

3. HDL Remote Server

1. The "Local" mode works only in the local network and it does not allow to set up control of the bus via the Internet. The broadcast address is used for connection. The local connections works with any HDL IP module.

2. The "Internet" mode enables connection to the HDL IP module via the Internet without using HDL Remote Server. In the "Internet" mode the connection is established directly between the panel and the HDL IP module. In order to work in this mode the router of the HDL network has to have the static IP-address and use the DDNS service.

HDL IP interface with firmware not earlier than HDL_V04.06U

3. The "HDL Remote Server" mode enables connection to the HDL IP module via the Internet if you do not have a static IP-address or domain (DDNS). The connection is established via the HDL Internet server which is used for authorization between the iRidium control panel and the HDL IP interface. After the authorization the connection is direct without using the server.

HDL IP interface with firmware not earlier than HDL_V04.06U

Bus scanning

Scanning works only in the local network - it enables fast adding of all HDL devices with preset commands in the project.

Create a new project and click the Scan > HDL-BUS Pro network scanner button in the Devices window, choose devices to add to the project:

before scanning close HDL Buspro Setup Tool.

As a result of scanning you will have three levels of the HDL bus:

HDL-Buspro Network (UDP) - the HDL bus, it unites all controlled devices (relays, sensors, etc.). The bus has an IP-address for external control via the HDL IP interface
HDL Devices - the devices in the bus. They have unique addresses - Subnet ID and Device ID
Commands and Feedbacks - the commands and feedback channels inside the devices which enable control of their separate properties.

If you cannot scan the bus, add HDL Buspro Network and devices manually:

Settings for connection to the bus

You can choose the HDL Buspro Network driver and set it to work with the device depending on what way of control your equipment supports.

Serial

Protocol - Serial.
Host - the IP address or domain name.
Used with iRidi device - set the host for the corresponding equipment (if this parameter is selected, the Host line will be inactive).
Baud Rate - the speed of data exchange with the controller
Data Bits - the number of information bits in a frame
Parity - parity control
Stop Bits - the stop bit in a frame (1; 1,5; 2).
Send Timeout - forced interval between commands that the control panel sends to the HDL IP module (it helps reduce the load on the IP module and HDL bus).

In the web interface, stop bits are displayed as:

iRidium studio:	Web interface:
1	0
1,5	1
2	2

If a direct IP-address of the gateway is used in the driver (for example, 192.168.0.5), the Need Confirm parameter of all commands is always turned on regardless of the settings in channel parameters. When a broadcast address is used (255.255.255.255), this parameres can be turned on or off for each channel (it is off by default for all channels).

Local

The "Local" mode works only in the local network and it does not allow you to set up control of the bus via the Internet. The broadcast address is used for connection. The local connections works with any HDL IP module.

In the settings of the HDL IP module indicate Network Parameter to work in the local network

IP: the local address of the HDL IP module
Subnet Mask: the subnet mask
Route IP: the default gateway

In the settings of HDL Gateway indicate the local address for connection with the HDL IP module. On the recommendation of your system administrator you can change the broadcast address. Otherwise, leave the default setting.

Host: 255.255.255.255 – the broadcast address for exchanging data with HDL
Send Timeout: the forced interval between commands sent by the control panel to the HDL IP module (it helps to decrease the load on the IP module and the HDL bus)
Connect Mode: Local – the mode for local connection with the HDL IP module
Fast Feedback:

emulation of quickly displaying feedback value on an element

Internet

The "Internet" mode enables connection to the HDL IP module via the Internet without using HDL Remote Server. In the "Internet" mode the connection is established directly between the panel and the HDL IP module. In order to work in this mode the router of the HDL network has to have the static IP-address and use the DDNS service.

HDL IP interface with firmware not earlier than HDL_V04.06U
access to the bus via Internet can be via one licensed HDL IP interface (concurrent connection to several HDL IP interfaces via the Internet is not supported)

In the settings of the HDL IP module indicate Connection Preferences: properties for connection to the HDL IP module

Type: Remote Server
Project Name, Group Name: the names of the project and group of projects
User, Password: the properties of the protected connection
Preferred Server, Port: the properties of connection to the HDL Remote Server (they will not be used in the “Internet” mode, but have to be indicated)

Send Timeout: the forced interval between commands sent by the control panel to the HDL IP module (it helps to decrease the load on the IP module and the HDL bus)
Connect Mode: Internet – the mode of connection with the HDL IP module
Host: the public IP-address of your router for accessing to the HDL IP module via the router
Port: the HDL port for direct connection to the HDL IP module via the Internet (6000)
Login: the login for connection, from the Remote Server settings of the IP module
Password: the password for connection, from the Remote Server settings of the IP module
Project Name: the project name from the Remote Server settings of the IP module

To work via the Internet, indicate the public IP-address of the router to which the controller is connected and set up Port Forwarding.

You can see the public IP-address of the router here

HDL Remote Server

The "HDL Remote Server" mode enables connection to the HDL IP module via the Internet if you do not have a static IP-address or domain (DDNS). The connection is established via the HDL Internet server which is used for authorization between the iRidium control panel and the HDL IP interface. After the authorization the connection is direct without using the server.

The list of available HDL remote servers you can find in HDL Tool in the Bus Scan winow after you switch the connection mode from "Local" to "Server"

HDL IP interface with firmware not earlier than HDL_V04.06U
access to the bus via Internet can be via one licensed HDL IP interface (concurrent connection to several HDL IP interfaces via the Internet is not supported)

In the settings of the HDL IP module indicate Connection Preferences: properties of the clients which have to have the possibility to connect to the HDL IP module

Type: Remote Server
Project Name, Group Name: the names of the project and group of projects
User, Password: the properties of protected connection
Preferred Server, Port: the properties for connection to the HDL server

In the settings of HDL Gateway (UDP) indicate properties of connection with the HDL IP module via the remote server.

Host: the address of the remote HDL server. The list of available HDL remote servers you can find in HDL Tool in the Bus Scan winow after you switch the connection mode from "Local" to "Server"
Port: the port of connection to the IP module via the remote server (as in the settings of the IP module)
Login: the login for connection, from the settings of the IP module
Password: the password of connection, from the settings of the IP module
Send Timeout: the forced interval between commands sent by the control panel to the HDL IP module (it helps to decrease the load on the IP module and the HDL bus)
Connect Mode: Remote Server – the mode of connection with the HDL IP module
Project Name: the project name, from the settings of the IP
Remote Server Priority: connect to the remote server first
External Port: port to access to HDL IP interface. If the field is empty, it will be filled with data received from HDL Server module
Group Name: the group name

Sometimes it is needed to forward the 6000 port (External Port) using instruction to work via Remote Server

Changing the connection settings

You need the possibility to change connection properties when you disconnect from the Wi-Fi network of the automation object and start using 3G or another Wi-Fi network. To maintain control of the object you need to switch from the local to public IP-address of the Internet router.

The switch is not automatic. You have to select the connection mode. For remote acces you have to make ports for controlling the automation system public. In order to do that you have o set up the Port Forwarding service on your Internet router. VPN can provide protected connection.

1 Download the template (*.js) (right-click button: "Save object as ..."), add the template in the script editor with the button (+) Add Script from file

2 Set up script properties as it is shown in the example:

function Internal_1() { IR.GetDevice('HDL-BUS Pro Network (UDP)').SetParameters({Host: "255.255.255.255", Port: 6000, SendNeedConfirm: 0, SendTimeout: 20, ConnectMode: 0}); }

function External_1() {

IR.GetDevice('HDL-BUS Pro Network (UDP)').SetParameters({Host: "215.110.10.10", Port: 6000, Login: "User", Password: "User", SendNeedConfirm: 0, SendTimeout: 20, ConnectMode: 3, ExtendedPort: 6000, Project: "ir_proj", Group: "ir_group"});

}

Copy the driver name from Projeсt Device Panel - the list of properties has to be copied from the example.

3 Select the button which will be responsible for the switch of Internal and External properties. Open Macros Editor for the Press event (Object Properties > Programming), select the Script Call command and add it by double-clicking on it. Select the name of the function which will be activated by the button:

Now each pressing on the button will apply the corresponding connection properties.

Examples:

// Local (ConnectMode=0)
IR.GetDevice("HDL Buspro UDP").SetParameters({Host: "255.255.255.255", Port: 6000, SendNeedConfirm: 0, SendTimeout: 20, ConnectMode: 0})
 
// Internet (ConnectMode=2)
IR.GetDevice("HDL Buspro UDP").SetParameters({Host: "215.110.10.10", Port: 6000, Login: "User", Password: "User", SendNeedConfirm: 0, SendTimeout: 20, ConnectMode: 3, Project: "ir_proj"})
 
// HDL Remote Server (ConnectMode=3)
IR.GetDevice("HDL Buspro UDP").SetParameters({Host: "215.110.10.10", Port: 9999, Login: "User", Password: "User", SendNeedConfirm: 0, SendTimeout: 20, ConnectMode: 3, ExtendedPort: 6000, Project: "ir_proj", Group: "ir_group"})

Devices

Device categories to which HDL devices can be related to at scanning the bus. The list includes devices available on hdlautomation.com at the moment of writing the article and supported by iRidium.

The list of device commands can be changed after scanning or manual adding in the project.

Contact the support team - (support@iridiummobile.ru) if it is required to update the list or you found some inaccuracy.

category	device	operation codes
Panels
	Switch Panel	Panel Control
	DLP Panel	Panel Control, Read Temperature
	DLP Panel (AC, FH)	Panel Control, Read Temperature, Floor Heating from DLP
	HDL Granite Panel	Panel Control, Floor Heating Control (DLP), Read Temperature, Read Temperature New, Read Analog Value
Dimming Actuators
	Dimmer - 1CH	Lighting
	Dimmer - 2CH	Lighting
	Dimmer - 4CH	Lighting
	Dimmer - 6CH	Lighting
	Dimmer - 12CH	Lighting
Relay Actuators
	Relay - 4CH	Lighting
	Relay - 8CH	Lighting
	Relay - 12CH	Lighting
	Relay - 16CH	Lighting
LED Actuators
	RGB LED Driver - 3CH	Lighting
	LED Dimmer - 6CH	Lighting
DALI Actuators	DALI Dimmer - 64CH	Lighting
DMX Actuators
	DMX Gateway - 16CH	Lighting
	DMX Controller - 512CH	Lighting
	DMX Controller - 48CH	Lighting
0-10V Actuators	Ballast Controller - 6CH + 6CH	Lighting
Sensors
	Ourdoor Sensor	Read Sensor Status (Sensors in One); Universal Switch (201-248)
	Sensor with 12 functions	Read Sensor Status (12in1, 8in1 314), Universal Switch
	Mini Ceiling Sensor (4 in 1)	Read Sensor Status (Sensors in One); Universal Switch (201-248)
	Ceiling Mount Sensor Temp-Hum-Lux
	Ceiling Mount Sensor Air Quality
	Ceiling Mount Sensor 8-In-1
	Ceiling Mount Sensor 7-In-1
	Ceiling Mount Mini Sensor PIR
	Movement sensor for ceiling-mounting
	Wall Mount Sensor UItrasonic-PIR
	Wall Mount Sensor Wide Field PIR
Security
	Security Module	Security, Universal Switch
	Logic Module	Logic, Universal Switch
Climate Actuators
	Temperature Sensor - 4CH	Read Temperature New
	Floor Heating Module - 6CH	Floor Heating from Heating Module, Universal Switch
	HVAC Module	AC
Shading Actuators
	Curtain Module - 2CH	Curtain Switch
	Motorized Curtain - 1CH + %	Curtain Switch
	Tubular Blind Controller - 1CH + %	Curtain Switch
Background Audio
	Z-Audio	Music
	Music Box	Music
Hotel System	Hotel RCU Room Controller Unit	Lighting, Curtain Switch, Universal Switch
Communication Gateways
	IR Emitter	Universal Switch
	SMS Module	GPRS, Universal Switch
	KNX Port	Universal Switch
	RS232 Converter	Universal Switch
Smart Metering
	Power Meter - 3 PHASE	Power Meter
	Power Meter - 1 PHASE	Power Meter
Dry Contact
	Dry Contact - 4CH	Dry Contact, Universal Switch
	Dry Contact - 8CH	Dry Contact, Universal Switch
	Dry Contact - 24CH	Dry Contact, Universal Switch

Setting Commands and Feedback Channels

To control equipment it is required to set Commands and Feedbacks. To send a command, drag'n'drop it on a graphic item and enter a value to send. To display feedback drag'n'drop a feedback channel on a graphic item and choose how to output or display a value.

Read more about work with graphic items in the "Types of graphic items" article.

Possible settings of commands, channels and graphic items when working with different operation codes:

Lighting

Single Channel Lighting

The command with feedback: control of dimmer brightness, switching relays on/off.

Select the HDL device, егоindicate its Subnet ID / Device ID, select the device type: Dimmer, Relay. Now you can set up comamnds for controlling channels brightness and receiving data about their states.

Command:

Operation Code	Single Channel Lighting	the command for setting up channel brightness
Channel	1-254	the number of the relay (dimmer) channel
Channel	255	all relay (dimmer) channels
Running Time (s)	0-14	the time during which brightness is changed
Need Confirm	Disable/Enable	to wait for the confirmation about command delivery from the bus (it is not recommended)
Use Timer	false	not to use timer for automatic repeat of the command
	0	to send the command once, at the application launch
	1...n	(c) to repeat the command with the indicated interval
Value *	0	to switch off
	100	to switch on
	0-100	to set up channel brightness (only for dimmers)

* Value - indicate it when dragging the command on graphic items

Feedback:

Operation Code	Single Channel Lighting	the current channel brightness
Channel	1-254	the number of the relay (dimmer) channel
Value	0-100	the current channel brightness for displaying on graphic items

Read Status of Channels

Command: to request the current brightness value of dimmer/relay channels. Feedback comes to the channel "Single Channel Lighting". It is usually used with Timer: 0 to get the dimmer/relay state at the application launch.

Select the HDL device, indicate its Subnet ID / Device ID, select the device type: Dimmer, Relay. Now you can set up the command of requesting the dimmer/relay state:

Command:

Operation Code	Read Status of Channels	to get the value for which the channel aims
Operation Code	Single Channel Read Actual	to get the channel brightness at the moment of the request
Channel	1-255	to send the request to one dimmer/relay channel
Channel	0	to send the request to all dimmer/relay channels
Need Confirm	Disable/Enable	to wait for the confirmation about request delivery from the bus (it is not recommended)
Use Timer	false	not to use timer for automatic repeat of the request
	0	to send the request once, at the application launch
	1...n	(c) to repeat the request with the indicated interval
Value	-	it is not used (you can leave it empty or write zero)

It is recommended to set up Use Timer: 0 - the command will be sent to equipment at the application launch. You do not need to assign the command to graphic items. You do not need to use the command during work as dimmers and relays send their status to the bus automatically.

Scene Control

Command: to start the scene saved in the dimmer/relay memory. Scenes are set up for devices of one Area.

Select the HDL device, indicate its Subnet ID / Device ID, select the device type: Dimmer, Relay. Now you can set up the command of starting the scene:

Command:

Operation Code	Scene Control	to start the scene
Area Number	1-255	the number of the Area for which the scene is set up
Need Confirm	Disable/Enable	to wait for the confirmation about command delivery from the bus (it is not recommended)
Use Timer	false	not to use timer for automatic repeat of the command
	0	to send the command once, at the application launch
	1...n	(c) to repeat the command with the indicated interval
Value *	0-255	the scene number

* Value - indicate it when dragging the command on graphic items

Sequence Control

Command: to start the sequence saved in the dimmer/relay memory. Sequences are set up for devices of one Area.

Select the HDL device, indicate its Subnet ID / Device ID, select the device type: Dimmer, Relay. Now you can set up the command of starting the sequence:

Command:

Operation Code	Sequence Control	to start the sequence of commands
Area Number	1-255	the number of the Area for which the sequence is set up
Need Confirm	Disable/Enable	to wait for the confirmation about command delivery from the bus (it is not recommended)
Use Timer	false	not to use timer for automatic repeat of the command
	0	to send the command once, at the application launch
	1...n	(c) to repeat the command with the indicated interval
Value *	0-255	the sequence number

* Value - indicate it when dragging the command on graphic items

Logic

Logic Control

Command with feedback: control of the logic unit state.

Select the HDL device, indicate its Subnet ID / Device ID, select the device type with support of commands for controling logic units. Now you can set up the commands:

Command:

Operation Code	Logic Control	to set up the state of the logic unit
Logic Block No.	1-255	the number of the logic unit
Need Confirm	Disable/Enable	to wait for the confirmation about command delivery from the bus (it is not recommended)
Use Timer	false	not to use timer for automatic repeat of the command
	0	to send the command once, at the application launch
	1...n	(c) to repeat the command with the indicated interval
Value *	0	Disable
	1	Enable

* Value - indicate it when dragging the command on graphic items

Feedback:

Operation Code	Logic Control	the state of the logic unit
Logic Block No.	1-255	the number of the logic unit
Value	0/1	the state of the logic unit (0 - Disable, 1 - Enable)

Read Status of Logic

Command: to request the current state of the logic unit. Feedback comes to the channel "Logic Control".

Select the HDL device, indicate its Subnet ID / Device ID, select the device type with support of commands for controling logic units. Now you can set up the command:

Command:

Operation Code	Read Status of Logic	to request the state of the logic unit
Logic Block No.	1-255	the number of the logic unit
Need Confirm	Disable/Enable	to wait for the confirmation about command delivery from the bus (it is not recommended)
Use Timer	false	not to use timer for automatic repeat of the command
	0	to send the command once, at the application launch
	1...n	(c) to repeat the command with the indicated interval
Value	-	it is not used (you can leave it empty or write zero)

It is recommended to set up Use Timer: 0 - the command will be sent to equipment at the application launch. You do not need to assign the command to graphic items. You can use the command during application work to request the unit state at a particular moment.

Universal Switch

Universal Switch Control

Command with feedback: control of the universal switch state.

Select the HDL device, indicate its Subnet ID / Device ID, select the device type with support of commands for controling the universal switch. Now you can set up the commands:

Command:

Operation Code	Universal Switch Control	to set up the state of the universal switch
Universal Number	1-255	the number of the universal switch
Need Confirm	Disable/Enable	to wait for the confirmation about command delivery from the bus (it is not recommended)
Use Timer	false	not to use timer for automatic repeat of the command
	0	to send the command once, at the application launch
	1...n	(c) to repeat the command with the indicated interval
Value *	0	OFF
	255	ON. The same value used to send the IR command. Universal Number is a number of the IR command in the memory of the transmitter. As a feedback you'll receive the value 1

* Value - indicate it when dragging the command on graphic items

Feedback:

Operation Code	Universal Switch Control	the state of the universal switch
Universal Number	1-255	the number of the universal switch
Value	0/1	the state of the universal switch (0 - OFF, 1 - ON)

Only Dry contact with not more than 32 set up universal switches sends data about changes of its status automatically. The state of the rest devices have to be requested to display feedback.

UV Switch for Floor Heating

Universal Switch Control commands for the module of floor heating SB-DN-FH06 (HDL_V04.10U_2014/06/06). They enable setting up work properties of all or separate channels of the module.
OFF = 0, ON = 255 (value to send).

FH	Switch	Value	Action
ALL CH	1	ON/OFF	ON/OFF
ALL CH	2	ON	Normal
ALL CH	3	ON	Day
ALL CH	4	ON	Night
ALL CH	5	ON	Away
ALL CH	6	ON	Timer
ALL CH	7	ON	Heat->Cool
ALL CH	7	OFF	Cool->Heat

FH	Switch	Value	Action
CH1	11	ON/OFF	ON/OFF
CH1	12	ON	Normal
CH1	13	ON	Day
CH1	14	ON	Night
CH1	15	ON	Away
CH1	16	ON	Timer
CH1	17	ON	Heat->Cool
CH1	17	OFF	Cool->Heat
CH1	70	ON	6C
CH1	71	ON	7C
CH1	72	ON	8C
CH1	73	ON	9C
CH1	74	ON	10C
CH1	75	ON	11C
CH1	76	ON	12C
CH1	77	ON	13C
CH1	78	ON	14C
CH1	79	ON	15C
CH1	80	ON	16C
CH1	81	ON	17C
CH1	82	ON	18C
CH1	83	ON	19C
CH1	84	ON	20C
CH1	85	ON	21C
CH1	86	ON	22C
CH1	87	ON	23C
CH1	88	ON	24C
CH1	89	ON	25C
CH1	90	ON	26C

FH	Switch	Value	Action
CH2	21	ON/OFF	ON/OFF
CH2	22	ON	Normal
CH2	23	ON	Day
CH2	24	ON	Night
CH2	25	ON	Away
CH2	26	ON	Timer
CH2	27	ON	Heat->Cool
CH2	27	OFF	Cool->Heat
CH2	95	ON	6C
CH2	96	ON	7C
CH2	97	ON	8C
CH2	98	ON	9C
CH2	99	ON	10C
CH2	100	ON	11C
CH2	101	ON	12C
CH2	102	ON	13C
CH2	103	ON	14C
CH2	104	ON	15C
CH2	105	ON	16C
CH2	106	ON	17C
CH2	107	ON	18C
CH2	108	ON	19C
CH2	109	ON	20C
CH2	110	ON	21C
CH2	111	ON	22C
CH2	112	ON	23C
CH2	113	ON	24C
CH2	114	ON	25C
CH2	115	ON	26C

FH	Switch	Value	Action
CH3	31	ON/OFF	ON/OFF
CH3	32	ON	Normal
CH3	33	ON	Day
CH3	34	ON	Night
CH3	35	ON	Away
CH3	36	ON	Timer
CH3	37	ON	Heat->Cool
CH3	37	OFF	Cool->Heat
CH3	120	ON	6C
CH3	121	ON	7C
CH3	124	ON	10C
CH3	122	ON	8C
CH3	125	ON	11C
CH3	123	ON	9C
CH3	126	ON	12C
CH3	127	ON	13C
CH3	128	ON	14C
CH3	129	ON	15C
CH3	130	ON	16C
CH3	131	ON	17C
CH3	132	ON	18C
CH3	133	ON	19C
CH3	134	ON	20C
CH3	135	ON	21C
CH3	136	ON	22C
CH3	137	ON	23C
CH3	138	ON	24C
CH3	139	ON	25C
CH3	140	ON	26C

FH	Switch	Value	Action
CH4	41	ON/OFF	ON/OFF
CH4	42	ON	Normal
CH4	43	ON	Day
CH4	44	ON	Night
CH4	45	ON	Away
CH4	46	ON	Timer
CH4	47	ON	Heat->Cool
CH4	47	OFF	Cool->Heat
CH4	145	ON	6C
CH4	146	ON	7C
CH4	147	ON	8C
CH4	148	ON	9C
CH4	149	ON	10C
CH4	150	ON	11C
CH4	151	ON	12C
CH4	152	ON	13C
CH4	153	ON	14C
CH4	154	ON	15C
CH4	155	ON	16C
CH4	156	ON	17C
CH4	157	ON	18C
CH4	158	ON	19C
CH4	159	ON	20C
CH4	160	ON	21C
CH4	161	ON	22C
CH4	162	ON	23C
CH4	163	ON	24C
CH4	164	ON	25C
CH4	165	ON	26C

FH	Switch	Value	Action
CH5	51	ON/OFF	ON/OFF
CH5	52	ON	Normal
CH5	53	ON	Day
CH5	54	ON	Night
CH5	55	ON	Away
CH5	56	ON	Timer
CH5	57	ON	Heat->Cool
CH5	57	OFF	Cool->Heat
CH5	170	ON	6C
CH5	171	ON	7C
CH5	172	ON	8C
CH5	173	ON	9C
CH5	174	ON	10C
CH5	175	ON	11C
CH5	176	ON	12C
CH5	177	ON	13C
CH5	178	ON	14C
CH5	179	ON	15C
CH5	180	ON	16C
CH5	181	ON	17C
CH5	182	ON	18C
CH5	183	ON	19C
CH5	184	ON	20C
CH5	185	ON	21C
CH5	186	ON	22C
CH5	187	ON	23C
CH5	188	ON	24C
CH5	189	ON	25C
CH5	190	ON	26C

FH	Switch	Value	Action
CH6	61	ON/OFF	ON/OFF
CH6	62	ON	Normal
CH6	63	ON	Day
CH6	64	ON	Night
CH6	65	ON	Away
CH6	66	ON	Timer
CH6	67	ON	Heat->Cool
CH6	67	OFF	Cool->Heat
CH6	195	ON	6C
CH6	196	ON	7C
CH6	197	ON	8C
CH6	198	ON	9C
CH6	199	ON	10C
CH6	200	ON	11C
CH6	201	ON	12C
CH6	202	ON	13C
CH6	203	ON	14C
CH6	204	ON	15C
CH6	205	ON	16C
CH6	206	ON	17C
CH6	207	ON	18C
CH6	208	ON	19C
CH6	209	ON	20C
CH6	210	ON	21C
CH6	211	ON	22C
CH6	212	ON	23C
CH6	213	ON	24C
CH6	214	ON	25C
CH6	215	ON	26C

UV Switch for IR Emitter

Control of IR emitters in HDL sensors and separate emitters is performed with the help of the Universal Switch command.

The installer saves the list of IR commands (up to 254 commands) in the memory of the IR emitter and iRidium calls a command by sending its number to the emitter.

Command:

Operation Code	Universal Switch Control	to set up the state of the universal switch, send the IR command
Universal Number	1-255	the IR command number in the emitter memory
Need Confirm	Disable/Enable	to wait for the confirmation about the command delivery from the bus (it is not recommended)
Use Timer	false	not to use the timer of automatic command repetition
	0	to send the iR command once, at the application launch
	1...n	(c) to repeat the IR command with the indicated interval
Value *	255	to send the IR command

* Value - indicate it when dragging the command on graphic items

Read Status of Universal Switch

Command: to request the current state of the universal switch. Feedback comes to the channel "Universal Switch Control".

Select the HDL device, indicate its Subnet ID / Device ID, select the device type with support of commands for controlling the universal switch. Now you can set up the command:

Command:

Operation Code	Read Status of Universal Switch	to request the state of the universal switch
Universal Number	1-255	the number of the universal switch
Need Confirm	Disable/Enable	to wait for the confirmation about command delivery from the bus (it is not recommended)
Use Timer	false	not to use timer for automatic repeat of the command
	0	to send the command once, at the application launch
	1...n	(c) to repeat the command with the indicated interval
Value	-	it is not used (you can leave it empty or write zero)

It is recommended to set up Use Timer: 0 - the command will be sent to equipment at the application launch. You do not need to assign the command to graphic items. You can use the command during application work to request the unit state at a particular moment.

IR Emitter

IR Control

Command:

Operation Code	IR Control	IR Control
Switch status	1/0	Switch status. 1 -detect, 0 - no detect.
Trigger button or dry contact	1..n	Optional.
Random number	0..255	Optional.
Need Confirm	Disable/Enable	To wait for the confirmation about command delivery from the bus (it is not recommended).
Use Timer	false	Not to use timer for automatic repeat of the command.
	0	To send the command once, at the application launch.
	1...n	To repeat the command with the indicated interval.

Feedback:

Operation Code	IR Control	IR Control
Function No.	1..n	Function number.

Curtain Switch

Curtain Switch Control

Command with feedback: control of the state of the 3-position relay for curtains, blinds and shutters

Select the HDL device, indicate its Subnet ID / Device ID, select the device type: Curtain. Now you can set up the commands:

Command:

Operation Code	Curtain Switch Control	to control the drive of the curtains controller
Curtain Number	1-16	the number of the controlled drive of the curtains controller
Curtain Number	17	to control the curtains position in the range 0...100% (only for controllers with 1 channel and described possibility of % control)
Need Confirm	Disable/Enable	to wait for the confirmation about command delivery from the bus (it is not recommended)
Use Timer	false	not to use timer for automatic repeat of the command
	0	to send the command once, at the application launch
	1...n	(c) to repeat the command with the indicated interval
Value *	0	Stop
	1	Up
	2	Down
	0-100	only for Сurtain Number: 17

* Value - indicate it when dragging the command on graphic items

Feedback:

Operation Code	Curtain Switch Control	the state of the drive of the curtains controller
Curtain Number	1-16	the number of the controlled drive of the curtains controller
Curtain Number	17	to activate control of the curtains position in the range 0...100% (only for controllers with 1 channel and described possibility of % control)
Value	0/1/2	Stop/Up/Down
Value	0-100	only for Сurtain Number: 17

Read Status of Curtain Switch

Command: to request the state of the curtains controller. Feedback comes to the channel "Curtain Switch Control".

Select the HDL device, indicate its Subnet ID / Device ID, select the device type: Curtain. Now you can set up the command:

Command:

Operation Code	Read Status of Curtain Switch	to request the state of the curtains controller
Curtain Number	1-16	the number of the controlled driveof the curtains controller
Curtain Number	17	to request the curtain position in the range 0...100% (only for controllers with 1 channel and described possibility of % control)
Need Confirm	Disable/Enable	to wait for the confirmation about command delivery from the bus (it is not recommended)
Use Timer	false	not to use timer for automatic repeat of the command
	0	to send the command once, at the application launch
	1...n	(c) to repeat the command with the indicated interval
Value	-	it is not used (you can leave it empty or write zero)

It is recommended to set up Use Timer: 0 - the command will be sent to equipment at the application launch. You do not need to assign the command to graphic items. You can use the command during application work to request the state at a particular moment.

GPRS

GPRS Control

Command: to send a message with the help of the GPRS module

Select the HDL device, indicate its Subnet ID / Device ID, select the device type: SMS Module. Now you can set up the commands:

Command:

Operation Code	GPRS Control	to send the message
GPRS Type	1	Message
Repetition	1...n	number of messages sent
Need Confirm	Disable/Enable	to wait for the confirmation about command delivery from the bus (it is not recommended)
Use Timer	false	not to use timer for automatic repeat of the command
	0	to send the command once, at the application launch
	1...n	(c) to repeat the command with the indicated interval
Value *	1-24	the number of the message group

* Value - indicate it when dragging the command on graphic items

Panel

Panel Control

Command with feedback: to control functions of the DLP panel including control of air conditioners (AC) and floor heating (Floor Heating), connected to the DLP panel.

Select the HDL device, indicate its Subnet ID / Device ID, select the device type: DLP Panel. Now you can set up the commands:

Command:

Operation Code	Panel Control	to control the DLP panel
Parameter		Option	Value *
1	IR Control	0	0 = OFF, 1 = ON
2	Lock Panel	0	0 = OFF, 1 = ON
3	AC Power	1-128 (Conditioner No.)	0 = OFF, 1 = ON
4	Cooling Temp	1-128 (Conditioner No.)	0-84
5	Fan Speed	1-128 (Conditioner No.)	0 = Auto, 1 = High, 2 = Medium, 3 = Low
6	AC Mode	1-128 (Conditioner No.)	0 = Cooling, 1 = Heating, 2 = Fan , 3 = Auto, 4 = Dehumidfy
7	Heat Temp	1-128 (Conditioner No.)	0-84
8	Auto Temp	1-128 (Conditioner No.)	0-84
9	Rise Temp	1-128 (Conditioner No.)	0-5
10	Decrease Temp	1-128 (Conditioner No.)	0-5
11	Back Light Status	0	0 = OFF, 1 = ON
12	Lock AC	0	0 = OFF, 1 = ON
13	Back LIght Level	0	0-100
14	Status Light Level	0	0-100
15	Shield Button	1-255 (Key No.)	Key Status 0 = Invalid, 1 = Valid
16	Shield Page	1-255 (Page No.)	Page Status 0 = Invalid, 1 = Valid
17	Control Button LED	1-255 (Key No.)	Key Status 0 = Invalid, 1 = Valid
18	Control Button	1-255 (Key No.)	Key Status 0 = Invalid, 1 = Valid - to trigger all the commands under it
19	Dry Temp	0	0-84
20	Temp Status	1-8 (Floor Heater No.)	0 = OFF, 1 = ON
21	Temp Mode	1-8 (Floor Heater No.)	1 = Normal, 2 = Day , 3 = Night, 4 = Away, 5 = Timer
22	FH Rise Temp	1-8 (Floor Heater No.)	0-5
23	FH Decrease Temp	1-8 (Floor Heater No.)	0-5
24	Lock Setup Page	1-8 (Floor Heater No.)	0 = OFF, 1 = ON
25	Normal Temp	1-8 (Floor Heater No.)	0-84
26	Day Temp	1-8 (Floor Heater No.)	0-84
27	Night Temp	1-8 (Floor Heater No.)	0-84
28	Away Temp	1-8 (Floor Heater No.)	0-84
Need Confirm	Disable/Enable	to wait for the confirmation about command delivery from the bus (it is not recommended)
Use Timer	false	not to use timer for automatic repeat of the command
	0	to send the command once, at the application launch
	1...n	(c) to repeat the command with the indicated interval

* Value - indicate it when dragging the command on graphic items

Feedback:

Operation Code	Panel Control	control of the DLP panel (the panel state)
Parameter	1-28	see the table of commands
Option		see the table of commands
Value		see the table of commands

Read Status of Panel

Command: to request the current state of one of the properties of the DLP panel. Feedback comes to the channel "Panel Control".

Select the HDL device, indicate its Subnet ID / Device ID, select the device type: DLP Panel. Now you can set up the command:

Command:

Operation Code	Read Status of Panel	to request the state of the selected property of the DLP panel
Parameter	1-28	see the table of properties #Panel Control
Need Confirm	Disable/Enable	to wait for the confirmation about command delivery from the bus (it is not recommended)
Use Timer	false	not to use timer for automatic repeat of the command
	0	to send the command once, at the application launch
	1...n	(c) to repeat the command with the indicated interval
Value	-	it is not used (you can leave it empty or write zero)

During application work you can use the command to request the panel property state at the selected time (on timer or with the help of graphic items)

AC

AC Control

Command with feedback: to control air conditioners via the HVAC module, without connecting to the DLP panel.

Select the HDL device, indicate its Subnet ID / Device ID, select the device type: AC. Now you can set up the commands:

Command:

Operation Code	AC Control	to control the air conditioner
Parameter		Value *
1	Temperature Type	0 = C, 1 = F
3	Cooling Temp Point	0-86
4	Heating Temp Point	0-86
5	Auto Temp Point	0-86
6	Dry Temp Point	0-86
7	Mode	0 = Cooling, 1 = Heating, 2 = Fan, 3 = Auto, 4 = Dry
8	Fan	0 =Auto, 1 = High, 2 = Medium, 3 = Low
9	AC Status	0 = OFF, 1 = ON
10	Setup Mode	0 = Cooling, 1 = Heating, 2 = Fan, 3 = Auto, 4 = Dry
11	Setup Speed	0 =Auto, 1 = High, 2 = Medium, 3 = Low
16	Set Point Temperature	0-86
Option	1-128	condition number
Need Confirm	Disable/Enable	to wait for the confirmation about command delivery from the bus (it is not recommended)
Use Timer	false	not to use timer for automatic repeat of the command
	0	to send the command once, at the application launch
	1...n	(c) to repeat the command with the indicated interval

* Value - indicate it when dragging the command on graphic items

Feedback:

Operation Code	AC Control	to display the air conditioner state
Parameter		Value *
1	Temperature Type	0 = C, 1 = F
2	Current Temperature	0-99
3	Cooling Temp Point	0-86
4	Heating Temp Point	0-86
5	Auto Temp Point	0-86
6	Dry Temp Point	0-86
7	Mode	0 = Cooling, 1 = Heating, 2 = Fan, 3 = Auto, 4 = Dry
8	Fan	0 = Auto, 1 = High, 2 = Medium, 3 = Low
9	AC Status	0 = OFF, 1 = ON
10	Setup Mode	0 = Cooling, 1 = Heating, 2 = Fan, 3 = Auto, 4 = Dry
11	Setup Speed	0 = Auto, 1 = High, 2 = Medium, 3 = Low
12	Current Mode	0 = Cooling, 1 = Heating, 2 = Fan, 3 = Auto, 4 = Dry
13	Current Fan	0 = Auto, 1 = High, 2 = Medium, 3 = Low
14	Sweep	0 = Enable, 1 = Disable
15	Sweep Mode	0= No Sweep , 1 = Sweep Now
Option	1-128	the number of the air conditioner

* Value comes to the feedback channel. It can be used for displaying on items.

Read Status of AC

Command: to request the current state of one of the properties of the AC controller. Feedback comes to the channel "AC Control".

Select the HDL device, indicate its Subnet ID / Device ID, select the device type: AC. Now you can set up the command:

Feedback:

Operation Code	Read Status of AC	to request the air conditioner state
Parameter	0-128	the number of the air conditioner
Need Confirm	Disable/Enable	to wait for the confirmation about command delivery from the bus (it is not recommended)
Use Timer	false	not to use timer for automatic repeat of the command
	0	to send the command once, at the application launch
	1...n	(c) to repeat the command with the indicated interval
Value	-	it is not used (you can leave it empty or write zero)

During application work you can use the command to request the panel property state at the selected time (on timer or with the help of graphic items)

AC control New

Command:

Operation Code	AC Control	control of a conditioner
Parameter		Value *
1	Temperature Type	0 = C, 1 = F
3	Cooling Temp Point	0-86
4	Heating temperature	0-86
5	Auto Temp Point	0-86
6	Dry Temp Point	0-86
7	Mode	0 = Cooling, 1 = Heating, 2 = Fan, 3 = Auto, 4 = Dry
8	Fan	0 = Auto, 1 = High, 2 = Medium, 3 = Low
9	AC Status	0 = OFF, 1 = ON
12	Current Mode	0 = Cooling, 1 = Heating, 2 = Fan, 3 = Auto, 4 = Dry
13	Current Fan	0 = Auto, 1 = High, 2 = Medium, 3 = Low
14	Sweep	1 = Sweep, 0 = Else
17	Lock ac page	1 = Lock, 0 = Else

* Value - enter it when drag'n'dropping the command onto a graphic item.

Read Status of AC NEW

Command: to request the current state of one of the properties of the AC controller. Feedback comes to the "AC Control" channel.

Select the HDL device, enter its Subnet ID / Device ID, select the device type: AC. Now you can set the command:

Feedback:

Operation Code	Read Status of AC	request of conditioner state
Need Confirm	Disable/Enable	waiting for a confirmation from the bus about the command delivery (not recommended)
Use Timer	false	do not use a timer to repeat a command automatically
	0	send a command one time when the app is launched
	1...n	(c) repeat the command withe a set period
Value	-	is not used (the field can be left empty or enter zero)

During the app work a command can be used to request the parameter of the panel at a certain moment (with the help of a timer when the app is launched or with the help of a graphic item)

Floor Heating from DLP

Floor Heating Control (DLP)

Command with feedback: to control floor heating via the DLP panel.

Select the HDL device, indicate its Subnet ID / Device ID, select the device type: DLP Panel (AC, FH). Now you can set up the commands:

Command:

Operation Code	Floor Heating Control (DLP)	to control floor heating via the DLP panel
Parameter		Value *
1	Temperature Type	0 = C, 1 = F
3	Status	0 = OFF, 1 = ON
4	Mode	1 = Normal, 2 = Day , 3 = Night, 4 = Away, 5 = Timer
5	Normal Temperature	5-95
6	Day Temperature	5-95
7	Night Temperature	5-95
8	Away Temperature	5-95
Need Confirm	Disable/Enable	to wait for the confirmation about command delivery from the bus (it is not recommended)
Use Timer	false	not to use timer for automatic repeat of the command
	0	to send the command once, at the application launch
	1...n	(c) to repeat the command with the indicated interval
FH ID	0-8	floor heating number in HDL Buspro (required field)

* Value - indicate it when dragging the command on graphic items

Feedback:

Operation Code	Floor Heating Control (DLP)	to dispaly the status of floor heating via the DLP panel
FH ID	0-8	floor heating number in HDL Buspro (required field)
Parameter		Value *
1	Temperature Type	0 = C, 1 = F
2	Current Temperature	Value
3	Status	0 = OFF, 1 = ON
4	Mode	1 = Normal, 2 = Day , 3 = Night, 4 = Away, 5 = Timer
5	Normal Temperature	5-95
6	Day Temperature	5-95
7	Night Temperature	5-95
8	Away Temperature	5-95
9	Timer	0 = Day, 1 = Night

* Value comes to the feedback channel. It can be used for displaying on items.

Read Status of Floor Heating (DLP)

Command: to request the current state of one of the floor heating properties via the DLP panel. Feedback comes to the channel "Control Floor Heating Status".

Select the HDL device, indicate its Subnet ID / Device ID, select the device type: DLP Panel (AC, FH). Now you can set up the command:

Feedback:

Operation Code	Read Status of Floor Heating (DLP)	request the condition of the underfloor heating
Need Confirm	Disable/Enable	to wait for the confirmation about command delivery from the bus (it is not recommended)
Use Timer	false	not to use timer for automatic repeat of the command
	0	to send the command once, at the application launch
	1...n	(c) to repeat the command with the indicated
FH ID	0-8	floor heating number in HDL Buspro (required field)
Value	-	it is not used (you can leave it empty or write zero)

During application work you can use the command to request the floor heating state at the selected time (on timer or with the help of graphic items)

Floor Heating from Heating Module

Commands for controlling 6-channel floor heating module (for mounting on the DIN-rail). The comamnds are sent to the module directly, without using the DLP panel.

Floor Heating Module Control

Command with feedback: to control floor heating.

Select the HDL device, indicate its Subnet ID / Device ID, select the device type: Floor Heating Module. Now you can set up the commands:

Command:

Operation Code	Floor Heating Module Control	to control floor heating via the floor heating module
Parameter		Value *
1	Temperature Type	0 = C, 1 = F
3	Current Work Status	0 = Heating, 1 = Cooling, 2 = Heating power output, 3 = Cooling power output
4	Mode	1 = Normal, 2 = Day , 3 = Night, 4 = Away, 5 = Timer
5	Normal Temperature	5-95
6	Day Temperature	5-95
7	Night Temperature	5-95
8	Away Temperature	5-95
9	Current Work Status Enable	0 = OFF, 1 = ON
12	Vavle Status	0 = OFF, 1 = ON
15	Watering Time	1-30 min
Channel	1-8	the floor heating channel
Need Confirm	Disable/Enable	to wait for the confirmation about command delivery from the bus (it is not recommended)
Use Timer	false	not to use timer for automatic repeat of the command
	0	to send the command once, at the application launch
	1...n	(c) to repeat the command with the indicated

* Value - indicate it when dragging the command on graphic items

Feedback:

Operation Code	Floor Heating Module Control	to display the floor heating state
Parameter		Value *
1	Temperature Type	0 = C, 1 = F
2	Current Temperature	0-100
3	Current Work Status	0 = Heating, 1 = Cooling, 2 = Heating power output, 3 = Cooling power output
4	Mode	1 = Normal, 2 = Day , 3 = Night, 4 = Away, 5 = Timer
5	Normal Temperature	5-95
6	Day Temperature	5-95
7	Night Temperature	5-95
8	Away Temperature	5-95
9	Current Work Status Enable	0 = OFF, 1 = ON
10	Timer	0 = Day, 1 = Night
11	Valve Status	0 = OFF, 1 = ON
12	Valve Value	0-100 %
13	Watering Type	0 = Auto Running, 1 = Command from outside
14	Watering Flag	0 = OFF, 1 = ON
15	Watering Time	1-30 min

* Value comes to the feedback channel. It can be used for displaying on items.

Read Status of Floor Heating Module

Command: to request the current state of one of the floor heating properties. Feedback comes to the channel "Floor Heating Module Control".

Select the HDL device, indicate its Subnet ID / Device ID, select the device type: Floor Heating Module. Now you can set up the command:

Feedback:

Operation Code	Read Status of Floor Heating Module	to request the floor heating state
Channel	1-8	the floor heating channel
Need Confirm	Disable/Enable	to wait for the confirmation about command delivery from the bus (it is not recommended)
Use Timer	false	not to use timer for automatic repeat of the command
	0	to send the command once, at the application launch
	1...n	(c) to repeat the command with the indicated interval
Value	-	it is not used (you can leave it empty or write zero)

During application work you can use the command to request the floor heating properties at the selected time (on timer or with the help of graphic items)

Sensors In One

Read Sensor Status (8 in 1, Device Type 315)

Command with feedback: to read data of the 8-in-1 sensor.

Select the HDL device, indicate its Subnet ID / Device ID, select the device type: Sensor 8 in 1 (type 315). Now you can set up the commands:

Command:

Operation Code	Read Sensor Status	to request the sensor properties
Parameter	1-24	Logic Number
Need Confirm	Disable/Enable	to wait for the confirmation about command delivery from the bus (it is not recommended)
Use Timer	false	not to use timer for automatic repeat of the command
	0	to send the command once, at the application launch
	1...n	(c) to repeat the command with the indicated interval
Value *	-	it is not used (you can leave it empty or write zero)

* Value - indicate it when dragging the command on graphic items

Feedback:

Operation Code	Read Sensor Status	the sensor state
Parameter		Value *
1	Dry Contact 1 Status	0 = OFF, 1 = ON
2	Dry Contact 2 Status	0 = OFF, 1 = ON
4	Motion Snesor	0 = No movement, 1 = Movement
7	Delay Time -	value

* Value comes to the feedback channel. It can be used for displaying on items.
Out of date sensors supports: 3 - Lux (0/1), 5 - Switch 1 (0/1), 6 - Switch 2 (0/1)

Read Sensor Status (8 in 1, Device Type 314)

Command with feedback: to read data of the 8-in-1 sensor.

Select the HDL device, indicate its Subnet ID / Device ID, select the device type: Sensor 8 in 1 (type 314). Now you can set up the commands:

Command:

Operation Code	Read Sensor Status	to request the sensor properties
Need Confirm	Disable/Enable	to wait for the confirmation about command delivery from the bus (it is not recommended)
Use Timer	false	not to use timer for automatic repeat of the command
	0	to send the command once, at the application launch
	1...n	(c) to repeat the command with the indicated interval
Value *	-	it is not used

* Value - indicate it when dragging the command on graphic items

Feedback:

Operation Code	Read Sensor Status	the sensor state
Parameter		Value *
1	Current Temperature	0-80 (-20C – 60C)
2	Brightness	value
3	Motion	0 = No movement, 1 = Movement
5	Dry Contact 1 Status	0 = OFF, 1 = ON
6	Dry Contact 2 Status	0 = OFF, 1 = ON

* Value comes to the feedback channel. It can be used for displaying on items.
Out of date sensors supports: 4 - Sonex (0/1), 7 - Switch 1 (0/1), 8 - Switch 2 (0/1)

Read Sensor Status (12 in 1)

Command with feedback: to read data of the 12-in-1 sensor.

Select the HDL device, indicate its Subnet ID / Device ID, select the device type: Sensor 12 in 1. Now you can set up the commands:

Command:

Operation Code	Read Sensor Status	to request the sensor properties
Need Confirm	Disable/Enable	to wait for the confirmation about command delivery from the bus (it is not recommended)
Use Timer	false	not to use timer for automatic repeat of the command
	0	to send the command once, at the application launch
	1...n	(c) to repeat the command with the indicated interval
Value *	-	it is not used

* Value - indicate it when dragging the command on graphic items

Feedback:

Operation Code	Read Sensor Status	the sensor state
Parameter		Value *
1	Current Temperature	0-80 (-20C – 60C)
2	Brightness	Lux
3	Motion Sensor	0 = No movement, 1 = Movement
4	Sonic	0 = No movement, 1 = Movement
5	Dry Contact 1	0 = OFF, 1 = ON
6	Dry Contact 2	0 = OFF, 1 = ON

* Value comes to the feedback channel. It can be used for displaying on items.

Read Sensor Status (Sensors In One)

Command with feedback: to read data of "Sensors in One".

Select the HDL device, indicate its Subnet ID / Device ID, select the device type: Sensors In One. Now you can set up the commands:

Command:

Operation Code	Read Sensor Status	to request the sensor properties
Need Confirm	Disable/Enable	to wait for the confirmation about command delivery from the bus (it is not recommended)
Use Timer	false	not to use timer for automatic repeat of the command
	0	to send the command once, at the application launch
	1...n	(c) to repeat the command with the indicated interval
Value *	-	it is not used

* Value - indicate it when dragging the command on graphic items

Feedback:

Operation Code	Read Sensor Status	the sensor state
Parameter		Value *
1	Current Temperature	0-80 (-20 ... +60 °C)
2	Brightness	0-100
3	Humidity	20-95 % RH
4	Air	0 = Clean, 1 = Mild, 2 = Moderate, 3 = Severe
5	Gas	0-100%
6	Motion Sensor	0 = No movement, 1 = Movement
7	Dry Contact 1	0 = OFF, 1 = ON
8	Dry Contact 2	0 = OFF, 1 = ON
9	UV Switch 1	0 = OFF, 1 = ON
10	UV Switch 2	0 = OFF, 1 = ON
11	Sonex	0 = Null, 1 = Valid

* Value comes to the feedback channel. It can be used for displaying on items.

Read Temperature

Command with feedback: to read temperature of the DLP panel or another device with the temperature sensor.

Select the HDL device, indicate its Subnet ID / Device ID, select the device type: DLP Panel or another with the temperature sensor. Now you can set up the commands:

Command:

Operation Code	Read Temperature	to request data from the temperature sensor
Need Confirm	Disable/Enable	to wait for the confirmation about command delivery from the bus (it is not recommended)
Use Timer	false	not to use timer for automatic repeat of the command
	0	to send the command once, at the application launch
	1...n	(c) to repeat the command with the indicated interval
Value *	-	it is not used

* Value - indicate it when dragging the command on graphic items

Feedback:

Operation Code	Read Temperature	the sensor temperature
Channel	1-255	the number of the temperature sensor (for the DLP panel: 1)
Value *	the current temperature

* Value comes to the feedback channel. It can be used for displaying on items.

Read Temperature New

Command with feedback: to read temperature: the command of the new type with support of fractional values.

Select the HDL device, indicate its Subnet ID / Device ID, select the device type: DLP Panel or another with the temperature sensor. Now you can set up the commands:

Command:

Operation Code	Read Temperature	to request data from the temperature sensor
Need Confirm	Disable/Enable	to wait for the confirmation about command delivery from the bus (it is not recommended)
Use Timer	false	not to use timer for automatic repeat of the command
	0	to send the command once, at the application launch
	1...n	(c) to repeat the command with the indicated interval
Value *	-	it is not used

* Value - indicate it when dragging the command on graphic items

Feedback:

Operation Code	Read Temperature New	the sensor temperature
Channel	1-255	the number of the temperature sensor (for the DLP panel: 1)
Value *	the current temperature (float)

* Value comes to the feedback channel. It can be used for displaying on items.

Universal Control

Command with feedback: to control properties of different types of sensors with Universal Control support.

Select the HDL device, indicate its Subnet ID / Device ID, select the device type. Now you can set up the commands:

Command:

Operation Code	Universal Control	to set up the sensor property
Option		Value *
1	PIR sensitivity	1-100
2	Ultrasonic sensitivity	1-100
3	Temperature sensor validity	0 = Disable, 1 = Enable
4	LUX sensor validity	0 = Disable, 1 = Enable
5	Humidity sensor validity	0 = Disable, 1 = Enable
6	Air quality sensor validity	0 = Disable, 1 = Enable
7	PIR sensor validity	0 = Disable, 1 = Enable
8	Ultrasonic sensor validity	0 = Disable, 1 = Enable
9	Dry contact 1 validity	0 = Disable, 1 = Enable
10	Dry contact 2 validity	0 = Disable, 1 = Enable
Need Confirm	Disable/Enable	to wait for the confirmation about command delivery from the bus (it is not recommended)
Use Timer	false	not to use timer for automatic repeat of the command
	0	to send the command once, at the application launch
	1...n	(c) to repeat the command with the indicated interval

* Value - indicate it when dragging the command on graphic items

Feedback:

Operation Code	Universal Control	the state of the sensor properties
Option		Value
1	PIR sensitivity	1-100
2	Ultrasonic sensitivity	1-100
3	Temperature sensor validity	0 = Disable, 1 = Enable
4	LUX sensor validity	0 = Disable, 1 = Enable
5	Humidity sensor validity	0 = Disable, 1 = Enable
6	Air quality sensor validity	0 = Disable, 1 = Enable
7	PIR sensor validity	0 = Disable, 1 = Enable
8	Ultrasonic sensor validity	0 = Disable, 1 = Enable
9	Dry contact 1 validity	0 = Disable, 1 = Enable
10	Dry contact 2 validity	0 = Disable, 1 = Enable

* Value comes to the feedback channel. It can be used for displaying on items.

Analog Value

Command with feedback: to request properties of different types of sensors with Analog Value support.

Select the HDL device, indicate its Subnet ID / Device ID, select the device type. Now you can set up the commands:

Command:

Operation Code	Read Analog Value	to request the sensor property
Parameter	0-255	the channel number
Option	the type of the requested property
	0	Lux
	1	Temperature
	2	Power
	3	Current
	4	Pressure
Need Confirm	Disable/Enable	to wait for the confirmation about command delivery from the bus (it is not recommended)
Use Timer	false	not to use timer for automatic repeat of the command
	0	to send the command once, at the application launch
	1...n	(c) to repeat the command with the indicated interval
Value *	it is not used (you can leave it empty or write zero)

* Value - indicate it when dragging the command on graphic items

Feedback:

Operation Code	Read Analog Value	the sensor property
Parameter	0-255	the channel number
Option	the type of the requested property
	0	Lux
	1	Temperature
	2	Power
	3	Current
	4	Pressure
Value *	0-255	the value of the selected variable

* Value comes to the feedback channel. It can be used for displaying on items.

Security

Arm Security Module

Command with feedback: to set up the state of the security module. It sets up the current security mode (Arm) in the indicated Area.

add iRidium control panels in the list of devices which can control the security controller: Subnet ID: 253, Device ID: 254.

Select the HDL device, indicate its Subnet ID / Device ID, select the device type: Security Module. Now you can set up the commands:

Command:

Operation Code	Arm Security Module	to set up the security mode
Area	1-8	the security area
Need Confirm	Disable/Enable	to wait for the confirmation about command delivery from the bus (it is not recommended)
Use Timer	false	not to use timer for automatic repeat of the command
	0	to send the command once, at the application launch
	1...n	(c) to repeat the command with the indicated interval
Value *	to select the security mode (Arm)
6	Disarm
5	Day Arm
4	Night with Guest Arm
3	Night Arm
2	Away Arm
1	Vacation Arm

* Value - indicate it when dragging the command on graphic items

Feedback:

Operation Code	Arm Security Module	to display the current security mode
Area	1-8	the security area
Value *	the current security mode (Arm)
6	Disarm
5	Day Arm
4	Night with Guest Arm
3	Night Arm
2	Away Arm
1	Vacation Arm

* Value comes to the feedback channel. It can be used for displaying on items.

Read Status of Arm

Command with feedback: to request the mode of the security module. It returns the current security mode (Arm) in the indicated Area in the channel "Arm Security Module".

Select the HDL device, indicate its Subnet ID / Device ID, select the device type: Security Module. Now you can set up the commands:

Command:

Operation Code	Read Status of Arm	to request the current security mode
Area	1-8	the security area
Need Confirm	Disable/Enable	to wait for the confirmation about command delivery from the bus (it is not recommended)
Use Timer	false	not to use timer for automatic repeat of the command
	0	to send the command once, at the application launch
	1...n	(c) to repeat the command with the indicated interval
Value *	-	it is not used

* Value - indicate it when dragging the command on graphic items

It is recommended to set up Use Timer: 0 - the command will be sent to equipment at the application launch. You do not need to assign the command to graphic items. You do not need to use the command during work as the security module sends its status to the bus automatically.

Alarm Security Module

Command: to activate the alarm signal. The signal (Alarm) in the indicated Area is activated by the comamnd to the security module. You cannot display the status of alarm signals.

Select the HDL device, indicate its Subnet ID / Device ID, select the device type: Security Module. Now you can set up the commands:

Command:

Operation Code	Alarm Security Module	to activate the alarm signal
Area	1-8	the security area
Option		Value *
4	Current Alarm	0 = OFF, 1 = ON
5	Emergency Alarm	0 = OFF, 1 = ON
6	Panic Alarm	0 = OFF, 1 = ON
7	Gas Alarm	0 = OFF, 1 = ON
8	Fire Alarm	0 = OFF, 1 = ON
9	Temperature Alarm	0 = OFF, 1 = ON
10	Power Alarm	0 = OFF, 1 = ON
11	Silence Alarm	0 = OFF, 1 = ON
Need Confirm	Disable/Enable	to wait for the confirmation about command delivery from the bus (it is not recommended)
Use Timer	false	not to use timer for automatic repeat of the command
	0	to send the command once, at the application launch
	1...n	(c) to repeat the command with the indicated interval

* Value - indicate it when dragging the command on graphic items

Dry Contact

Read Status of Dry Contact

Command with feedback: to request the dry contact state

Select the HDL device, indicate its Subnet ID / Device ID, select the device type: Dry Contact. Now you can set up the commands:

Command:

Operation Code	Read Status of Dry Contact	to request the dry contact state
Area	1-255	the area
Input Number	1-255	the dry contact number
Need Confirm	Disable/Enable	to wait for the confirmation about command delivery from the bus (it is not recommended)
Use Timer	false	not to use timer for automatic repeat of the command
	0	to send the command once, at the application launch
	1...n	(c) to repeat the command with the indicated interval
Value *	it is not used

* Value - indicate it when dragging the command on graphic items

Feedback:

Operation Code	Read Status of Dry Contact	to read the dry contact state
Area	1-255	the area
Input Number	1-255	the dry contact number
Value *	0 = OFF, 1 = ON	the dry contact state

* Value comes to the feedback channel. It can be used for displaying on items.

Read Status of Dry Contact (security)

Command with feedback: to request the state of the dry contact set up for work with the security module, when the sensor is included in "Alarm List"

Select the HDL device, indicate its Subnet ID / Device ID, select the device type: Dry Contact. Now you can set up the commands:

Command:

Operation Code	Read Status of Dry Contact (security)	to request the state of the dry contact included in "Alarm List" of the security module
Area	1-255	the area
Input Number	1-255	the dry contact number
Need Confirm	Disable/Enable	to wait for the confirmation about command delivery from the bus (it is not recommended)
Use Timer	false	not to use timer for automatic repeat of the command
	0	to send the command once, at the application launch
	1...n	(c) to repeat the command with the indicated interval
Value *	it is not used

* Value - indicate it when dragging the command on graphic items

Feedback:

Operation Code	Read Status of Dry Contact (security)	to read the dry contact state
Area	1-255	the area
Input Number	1-255	the dry contact number
Value *	0 = OFF, 1 = ON	the current state of the dry contact

* Value comes to the feedback channel. It can be used for displaying on items.

Power Meter

Read Voltage

Command with feedback: to request the current voltage (A:1, B:2, C:3) of the meter

Select the HDL device, indicate its Subnet ID / Device ID, select the device type: Power Meter. Now you can set up the commands:

Command:

Operation Code	Read Voltage	to request the current voltage
Need Confirm	Disable/Enable	to wait for the confirmation about command delivery from the bus (it is not recommended)
Use Timer	false	not to use timer for automatic repeat of the command
	0	to send the command once, at the application launch
	1...n	(c) to repeat the command with the indicated interval
Value *	it is not used

* Value - indicate it when dragging the command on graphic items

Feedback:

Operation Code	Read Voltage	the current voltage
Parameter	1-3	the channel (phase) number
Value *	the current voltage

* Value comes to the feedback channel. It can be used for displaying on items.

Read Current

Command with feedback: to request the effective value of the alernating current (A:1, B:2, C:3, T:4)

Select the HDL device, indicate its Subnet ID / Device ID, select the device type: Power Meter. Now you can set up the commands:

Command:

Operation Code	Read Current	to request the effective value of the alternating current
Need Confirm	Disable/Enable	to wait for the confirmation about command delivery from the bus (it is not recommended)
Use Timer	false	not to use timer for automatic repeat of the command
	0	to send the command once, at the application launch
	1...n	(c) to repeat the command with the indicated interval
Value *	it is not used

* Value - indicate it when dragging the command on graphic items

Feedback:

Operation Code	Read Current	the effective value of the alternating current
Parameter	1-4	the channel (phase) number
Value *	the effective value of the alternating current

* Value comes to the feedback channel. It can be used for displaying on items.

Read Power

Command with feedback: to request the active power (A:1, B:2, C:3, T:4)

Select the HDL device, indicate its Subnet ID / Device ID, select the device type: Power Meter. Now you can set up the commands:

Command:

Operation Code	Read Power	to request the active power
Need Confirm	Disable/Enable	to wait for the confirmation about command delivery from the bus (it is not recommended)
Use Timer	false	not to use timer for automatic repeat of the command
	0	to send the command once, at the application launch
	1...n	(c) to repeat the command with the indicated interval
Value *	it is not used

* Value - indicate it when dragging the command on graphic items

Feedback:

Operation Code	Read Power	the active power
Parameter	1-4	the channel (phase) number	Value *	the active power

* Value comes to the feedback channel. It can be used for displaying on items.

Read Power Factor

Command with feedback: to request the power factor (A:1, B:2, C:3, T:4)

Select the HDL device, indicate its Subnet ID / Device ID, select the device type: Power Meter. Now you can set up the commands:

Command:

Operation Code	Read PowerFactor	to request the power factor
Need Confirm	Disable/Enable	to wait for the confirmation about command delivery from the bus (it is not recommended)
Use Timer	false	not to use timer for automatic repeat of the command
	0	to send the command once, at the application launch
	1...n	(c) to repeat the command with the indicated interval
Value *	it is not used

* Value - indicate it when dragging the command on graphic items

Feedback:

Operation Code	Read Power Factor	the power factor
Parameter	1-4	the channel (phase) number
Value *	the power factor

* Value comes to the feedback channel. It can be used for displaying on items.

Read Electricity

Command with feedback: to request the active energy (A:1, B:2, C:3, T:4)

Select the HDL device, indicate its Subnet ID / Device ID, select the device type: Power Meter. Now you can set up the commands:

Command:

Operation Code	Read Power Factor	to request the value of active energy
Need Confirm	Disable/Enable	to wait for the confirmation about command delivery from the bus (it is not recommended)
Use Timer	false	not to use timer for automatic repeat of the command
	0	to send the command once, at the application launch
	1...n	(c) to repeat the command with the indicated interval
Value *	it is not used

* Value - indicate it when dragging the command on graphic items

Feedback:

Operation Code	Read Power Factor	the value of active energy
Parameter	1-4	the channel (phase) number
Value *	the value of active energy

* Value comes to the feedback channel. It can be used for displaying on items.

Music

Music Control (DLP)

Commands have to be sent to Z-Audio, the DLP panel is not required.

Command with feedback: to control Z-Audio commands, the same commands DLP panels send. It allows you to get the list of Z-Audio tracks. Select the HDL device, indicate its Subnet ID / Device ID, select the device type: Z-Audio. Now you can set up commands for the available audio sources * (Source):

* Source:

1 – SD CARD
2 – NAS-HDD (FTP Server)
3 – SERVER
4 – WEB-RADIO
5 – RADIO
6 – AUDIO IN
7 – INTERCOM

Command:

Operation Code	Music Control (DLP)	to control playback
Command		Zone	Source *
0	POWER	1-9	-
1	STATUS REQUEST	1-9	-
2	SOURCE NEXT	1-9	-
3	VOLUME	1-9	-
4	MUTE	1-9	-
5	TONE REQUEST	1-9	-
6	BASS UP	1-9	-
7	BASS DOWN	1-9	-
8	TREBLE UP	1-9	-
9	TREBLE DOWN	1-9	-
10	PLAY/STOP	-	1-9
11	PLAY	-	1-9
12	STOP	-	1-9
13	PLAY MODE REQUEST	-	1-9
14	MODE NEXT	-	1-9
15	MODE PREV	-	1-9
16	LIST NEXT	-	1-9
17	LIST PREV	-	1-9
18	NEXT	-	1-9
19	PREV	-	1-9
20	CHADJ NEXT	-	1-9
21	CHADJ PREV	-	1-9
22	CHANNEL SCAN NEXT	-	1-9
23	CHANNEL SCAN PREV	-	1-9
24	CHANNEL NEXT	-	1-9
25	CHANNEL PREV	-	1-9
26	SAVE	-	1-9
27	UPDATE STATUS	-	1-9
28	UPDATE LIST	-	1-9
160	LIST	-	1-9
Need Confirm	Disable/Enable	to wait for the confirmation about command delivery from the bus (it is not recommended)
Use Timer	false	not to use timer for automatic repeat of the command
	0	to send the command once, at the application launch
	1...n	(c) to repeat the command with the indicated interval
Value	it is not used. Write 0 when dragging the command on items

Feedback:

Operation Code	Music Control (DLP)	the playback status
Command		Zone	Source *	Value **
128	SOURCE	1-9	-	1-9
129	VOLUM	1-9	-	0-100
130	DND	-	1-9
131	LOCK	-	1-9	0 = LOCKED, 1 = UNLOCKED
132	POSITION IN PERSENT	-	1-9	0-100
133	POSITION CURRENT	-	1-9	0-999.9 s
134	POSITION TOTAL	-	1-9	0-999.9 s
135	PLAY STATUS	-	1-9	1 = STOP, 2 = PLAY
136	PLAY MODE	-	1-9	1-4
137	LINE 1	-	1-9	List: No/Total
138	LINE 2	-	1-9	Playlist Name
139	LINE 3	-	1-9	Song: No/Total
140	LINE 4	-	1-9	Song Name
141	BASS	-	1-9	1-7
142	TREABLE	-	1-9	1-7
160	LIST	-	1 or 2	List ***

* Value comes to the feedback channel. It can be used for displaying on items.

*** List - the list of folders and tracks which can be displayed with the help of the List item, see the example of use below.

Displaying the list of tracks (the LIST command):

Z-AUDIO LIST

The List graphic item allows you to form the list of tracks and perform actions on clicking on the list items:

to open the folder on clicking on the list item - folder
to start playback on clicking on the list item - track
to return to the folder above when clicking on the first list item: [ ... ]

The list items will be organized on the basis of the template - the popup which has to be created in the project beforehand. Creation and filling in items are performed automatically. Item settings:

List, the item where the list of tracks will be displayed:

List Template: the name of the popup selected as the template for each list item.

Popup, the template of one list item:

The track name will be written in the text field of the popup, not the items on it.

Assign the LIST command to control the list and to display data:

Select the List graphic item, open the Programming tab
Select the Select event. In the macros editor for the Select event find the command Send To Driver > Send Token
In the Channel string select the LIST command for the SD or FTP source
In the Token string select the path to the List graphic item on the page or popup, the item property: SelectItem
Click ОК to save the command

Assign LIST feedback to display the list of Z-Audio tracks on the item:

In Project Device Panel select the LIST feedback channel from the SD or FTP source
Drag the feedback channel on the List graphic item, select "More..." in the dialog of assigning
Select the This property of the graphic item
Click ОК to save feedback

Now the command and feedback are set up, the item will display the list of Z-Audio tracks.

Music Control (TTP)

Command with feedback: the auxiliary TTPlayer command to control Z-Audio. The Z-Audio functions are fully covered by the Music Control (DLP) command, without requesting use of the DLP panel.

Select the HDL device, indicate its Subnet ID / Device ID, select the device type: Z-Audio. Now you can set up the commands:

Command:

Operation Code	Music Control (TTP)	to control playback
Parameter	Option	Value *
1 - Source selection	N/A	1 - SD card
		2 - External audio input
		3 - FTP server
		4 - Radio FM On
2 - Play mode	N/A	1 - Single playing
		2 - Single repetition
		3 - Order cycle
		4 - All repetition
3 - List/Channel	N/A	1 - Previous list
	N/A	2 - Next list
	1-255	3 - Select List Number
	N/A	4 - Previous channel
	N/A	5 - Next channel
	1-255	6 - Select Channel Number
4 - Play control	0-79	1 - Previous
		2 - Next
		3 - Play
		4 - Stop
5 - Volume	N/A	0 - Auto
		1 - High
		2 - Medium
		3 - Low
6 - Play	0-999 - Song	0-255 - List
Need Confirm	Disable/Enable	to wait for the confirmation about command delivery from the bus (it is not recommended)
Use Timer	false	not to use timer for automatic repeat of the command
	to send the command once, at the application launch
	1...n	(c) to repeat the command with the indicated interval

* Value - indicate it when dragging the command on graphic items

Feedback:

Operation Code

the playback status

Parameter

Option

Value *

see the table with description of the command list|}

* Value comes to the feedback channel. It can be used for displaying on items.

HomePlay Network Player

Installation, setting and a list of commands and feedback channels are the same as for Music Control (DLP).
To understand it better, download the example, enter Subnet ID / Device ID of the device.

download:

Example of work with HomePlay Network Player

HDL Granite Panel

To get data from sensors and to control equipment, use operation codes with the following settings:

Temperature:
- Read Temperature New (Chanel = 1),
- Read Temperature (Chanel = 1),
- Read Analog Value (Chanel = 0, Option = 65),
Humidity:
- Read Analog Value (Chanel = 0, Option = 69),
Voltage:
- Read Analog Value (Chanel = 0, Option = 2),
Control of warm floor:
- Panel Control (Parameter = 20~21, 25~28, Option = 1~8),
Temperature of warm floor:
- Floor Heating Control (DLP) (Parameter = 3~8, FH ID = 1~8).

A command with a corresponding feedback channel must be used in a project for correct work of equipment.

Download the example below and enter Subnet ID / Device ID.

download:

An example of project to work with HDL Granite Panel

Gate HDL to Dali

Read Color Temperature

Command: to request the current value of brightness or colors of dimmer channels. Feedback comes to the "Color temperature control" channel. Usually it is used with the following setting: Timer: 0 to get dimmer and relay states when the app is being launched.

Select the HDL device, indicate its Subnet ID / Device ID, select the device type: Gate HDL to Dali. Now you can set up the command of requesting the dimmer state.

Command:

Operation Code	Read Color Temperature	to request the state of dimmer color and brightness
Channel	1-255	number of a channel
Need Confirm	Disable/Enable	to wait for confirmation from the bus that the command has been sent (not recommended)
Use Timer	false	not to use the timer of automatic command repeat
	0	to send a command once when the app starts
	1...n	(c) to repeat the command with indicated interval
Value *	-	it is not used (you can leave ot empty or enter zero)

* Value - enter it when drag'n'dropping a command on a graphic item

Color temperature control

Command with feedback: control of dimmer brightness and color.

Select the HDL device, indicate its Subnet ID / Device ID, select the device type: Gate HDL to Dali. Now you can set up commands for controlling channel brightness and color and receiving data about their states.

Command:

Operation Code	Color temperature control	to control the state of dimmer brightness and color
Channel	1-255	number of a channel
Command	Brightness / Color	type of control (to control brightness or color)
Control Type	Single, CCT, RGB, RGBW, RGBWY	type of color control
Need Confirm	Disable/Enable	to wait for the confirmation from the bus that the command is sent (not recommended)
Use Timer	false	not to use the timer of automatic command repeat
	0	to send a command once when the app starts
	1...n	(c) to repeat the command with indicated interval
Value *	0...n	value of color or brightness depending on the seleted type

* Value - enter it when drag'n'dropping a command on a graphic item

Feedback:

Operation Code	Color temperature control	state of dimmer color or brightness
Channel	1-255	number of a channel
Command	Brightness / Color	channel type (brightness/color)
Control Type	Single, CCT, RGB, RGBW, RGBWY	type of color control

* Value comes to the feedback channel. It can be used for displaying on items.

HDL CMD Test. Testing Sent Commands

CMD test allows you to compare data that come from the i3 pro app with data that come from the HDL native app, other software or from equipment itself.

1 Launch the HDL Buspro app and open the "Tool" tab:

2 Enter identificators of the device that commands must be tracked (Subnet ID, Device ID):

3 Put a flag next to the "The object device" parameter.

4 Control equipment, data from commands will be displayed in the lower window.

Data can be sent to our technical support as a screenshot of the window or as a text file.