Эта страница является
переводом страницы
KIN TOUCH. Перевод выполнен на 100%.
iRidium for KIN TOUCH
Setting KIN TOUCH Video Intercom to Work with iRidium
The documentation was updated on 21.7.2023
Tested Device
| Model |
Description |
Appearance |
|
| KIN TOUCH |
indoor IP video intercom |
|
Sound Quality Check on the KIN TOUCH Model
Technical Specification of KIN TOUCH
| Characteristics |
Value
|
| Power supply |
12V DC or PoE
|
| Power consumption in standby mode |
290 mА (*)
|
| With the connected thermal resistor in standby mode |
750 mА (**)
|
| Power consumption in operating mode |
1000 mА
|
| With the connected thermal resistor in operating mode |
1500 mА (**)
|
| Screen technical specifications
|
| Diagonal |
25.5 cm
|
| Format |
16:9
|
| Resolution |
1 024*600 pixels
|
| Audio
|
| Codec |
PCMA/PCMU/GSM/G722
|
| Technical characteristics of cameras
|
| Resolution |
1280 (H)*720 (V)
|
| Viewing angle |
55º (H), 105º (V)
|
| Minimum illumination |
0.5 Lux
|
| Maximum talk time |
120 sec.
|
| Response time of the electric lock release relay |
1-9 sec.
|
| Delayed activation of the electric lock release relay |
0-9 sec.
|
| Open door sensor response time |
off, 30 sec., 60 sec.,120 sec., 180 sec., 250 sec.
|
| Capacity of identifiers (cards) |
100 000 cards
|
| Facial recognition system capacity |
6 000 faces
|
| Operating temperature |
-40 - 70 ºC
|
| Relative humidity |
20% - 80%, non-condensing
|
(*) In places with temperatures below -20 ºC, use a 12V DC 2A power supply instead of a PoE power supply.
(**) The internal thermal resistor is automatically activated when the ambient temperature drops below -20º C.
Connection KIN TOUCH
- Connect PoE power or 12V DC power to the KIN TOUCH intercom.
- Connect the SIP server to the same local network as the calling device in one subnet (with the same subnet mask).
- Set up KIN TOUCH.
To make a call from the intercom, you need to enter the apartment number.
Device
In the "DEVICE" section you can find technical information related to the panel.
- FERMAX MEET PANEL: Device type
- FIRMWARE: Firmware version
- DEVICE: Panel type and number
- SERIES NO.: Unique panel identification number
- MAC: MAC number of the panel
- IP: IP address assigned to this panel
KIN TOUCH General Settings
The "GENERAL SETTINGS" section allows you to the KIN panel identification parameters within a specific installation. Allows you to set the date and time.
TYPE: Choose panel identification parameters. Different options will appear, depending on the selected TYPE of panel.
Main input panel
A panel installed at one of the main inputs to the residential complex.
- DEVICE NO: Number corresponding to the main input where this panel is installed (1-9000). In case the main input is only one, leave this value as 1.
- DEVICE TAG: The text will be displayed on the monitor and on the concierge panel.
Block panel
Panel installed on an individual building or at the entrance to a block of a residential complex.
- BLOCK: Block number where this panel is installed (1-999). In case of individual blocks enter the default value: 1.
- DEVICE NO.: Block entrance number where the panel is installed (1-99). In case of units with one input enter the default value: 1.
- DEVICE TAG: The text will be displayed on the monitor and on the concierge panel.
Personal panel
For separate apartments or apartment buildings. You can only call one apartment.
- BLOCK Block number to which the apartment or apartment building belongs (1-999). In the case of apartments or separate apartments (not part of a block) enter the default value: 1.
- APARTMENT: Number of the apartment or house where this panel is installed (0001-9899).
- DESCRIPTION: Text to be displayed on the information panel for visitors.
- DEVICE NO: Number assigned to this panel (1-9). If there is only one panel, enter the default value of 1.
- DEVICE TAG: The text will be displayed on the monitor and at the concierge's desk.
- DESCRIPTION: Text for display on the panel for visitor information.
ALPHANUMERIC KEYBOARD: Check this box if the panel will use an alphanumeric keyboard or deactivate the box if only a numeric keyboard will be used. In case of using the ALPHABITAL keypad the characters A-H will be available additionally. The panel converts A to a digit 1, B to a digit 2, etc.. For example, when dialing 80C the call will be directed to monitor 803.
LANGUAGE: Choose the necessary language from the list:
By default, ENGLISH is chosen. Refresh the page, after changing the language.
SOUND LEVEL OF THE PANEL: Choose the necessary value for the conversation volume level in the range from 1 to 5. The selected volume will be for the street and for the apartment.
BRIGHTNESS: Choose a screen brightness value from 50, 100, 150, 200 and 250 (by default 250).
VOICE SYNTHESISER «DOOR OPEN»: Activates or deactivates the audible phrase indicating that the door is open. There will be no signal sound when the door is opened if this parameter is not selected.
VIDEO RESOLUTION: Adapting image resolution to match the monitor resolution. The default value is 640×480.
SIP REDIRECTION MODE: This function applies to devices in the SIP CALLS table. For more information, see the SIP CALLS section.
PARALLEL RINGING: When calling from the panel, both the internal monitor and all related SIP devices ring at the same time. When one of the devices answers, the other device stops ringing.
SERIAL RINGING: When calling from the panel, the internal monitor will ring for 30 seconds and if there is no answer, the call will be redirected to the associated SIP device or devices that will start ringing.
SCREEN SAVER: Enables or disables the panel screen saver. The splash screen appears when the panel is not active and no one is in front of it for 60 seconds. After a further 3 minutes, the panel turns off to save energy. The screen saver can be configured. Please contact our technical support to get more information.
HELP: Activates the HELP icon on the panel. The information on the HELP screen can be customized. Please contact our technical support to get more information.
STANDBY MODE INTERFACE: You can set the standby mode interface to CALL, HELP, or HANDBOOK.
CONCIERGE: From the drop-down list you can select 0, 1 or 2 concierge consoles. If 0 is selected, the CONSCIERGE PANEL icon will not appear on the panel. If 1 is selected, visitors will be able to call one concierge directly. If 2 is selected, visitors will be able to call 2 concierges directly. Each concierge has a number between 9901 and 9910, depending on the installation. In addition to direct calls, it is also possible to call concierges by dialling the relevant number directly as if it were a call to the apartment.
DATE FORMAT: The format in which the date information will be displayed on the screen.
DATE: Manual date setting (see note below).
TIME: Manual time setting (see note below).
TIME ZONE: Setting the time zone. Select the time zone and save.
SUMMER TIME: It is necessary to activate during SUMMER TIME and deactivate during winter time.
Setting Up the KIN TOUCH Network
To continue working with KIN TOUCH, the network must be set:
1. Open the KIN TOUCH web interface in a web browser.
To do this, you need to access the IP address provided in the instructions, which is 10.1.0.1 by default and enter the default administrator login and password:
- Login: admin.
- Password: 123456.
2. Click NETWORK button in the web-interface:
3. Set the ip address, subnet mask and subnet gateway available to the other devices in the Network Protocols settings
Setting Up SIP KIN TOUCH
To make calls between iRidium panels and to call from KIN TOUCH to i3 pro and back, SIP-server must be set correctly. To set the work of KIN TOUCH in the modes of SIP-server and SIP-subscriber at the same time, go to the SIP tab in the web-interface:
- Check the "ENABLE SIP" box.
- Enter ip in SIP SERVER.
- Enter the SIP USER.
- Enter the SIP PASS.
SIP Calls
In the web-interface, click the SIP CALLS button
This option allows generating calls to mobile devices (smartphones) when the installation does not have a MEET monitor connected to the apartment. A call can be received on up to 8 smartphones at the same time.
It is also possible to generate calls to several MEET devices and/or third party SIP devices at the same time, using the SIP protocol instead of the FERMAX MEET protocol. The panel needs to import a CSV file with information about the device or devices that will receive the call.
- Choose EXPORT or create a new CSV file to create a CSV table.
- Use Microsoft Excel to open the created CSV file.
- Cells A1 and B1 will contain the text: APARTMENT, NAME.
- Cells A2, A3, etc. contain the numbers to be typed on the panel. Cells B2, B3, etc. contain redirection addresses in the format: sip:user@IP_SIP_SERVER, where user is the identifier with which the called device is programmed on the SIP server, and IP_SIP_SERVER is the IP address of the SIP server.
Advanced Settings
In this section, you can make some advanced settings, such as speed dialing and calling through the handbook (phonebook).
SPEED DIALING: This feature is not available in this version.
URL: Specify the device that should receive the direct call with the appropriate format:
ONU (GPON): Required for activation in large SIP-based installations (GPON).
CALL DISPLAY: The installer can create a list of mapped calls, the mapping code can include numeric and alphanumeric code. For the access control panel the allowed number of characters is from 1 to 5. For the main entrance panel, the allowed number of characters is from 1 to 8. A visitor can call the apartment through the display code if the apartment has such a code. The visitor can call the apartment by means of a code or by means of the apartment number, if the apartment does not have a code.
WHITE LIST: You can call an apartment if it is marked with the letter Y in the "white list" column, otherwise it is not possible to call the apartment.
CATALOG: The KIN panel allows you to use the telephone directory to call apartments directly. Visitors can choose an apartment owner's name and call directly, without needing to know the apartment number.
SIP Driver Set Up In i3Pro Project
- Host: IP address of the SIP server;
Port: 5060;
- Password: user password Sip;
Caller ID: user name;
SIP ID: subscriber number, this number will be assigned to the equipment on which the project will be launched;
SIP server: Another;
- Codecs used.
