Эта страница является
переводом страницы
Kleger. Перевод выполнен на 100%.
iRidium for Kleger
a set of tools to create control interfaces for Kleger equipment.
The documentation was updated on 21.7.2021
iRidium for Kleger is a driver with a capability to add ready subdevices with a set of commands and feedback channels characteristic of this type. iRidium allows to emulate button presses from panels and to create an interface to control Kleger equipment.
Connection
Use Waveshare RS485 to ETH adapter for iRidium to work with Kleger devices. It functions as a gateway that sends a signal from iRidium that comes on the IP level to the bus with devices and back.
Define the IP-address of the converter, and if it is required make changes in the "Local IP Config" section. Later on IP must be entered in the driver settings.
Go to the "Serial Port" section and enter connection settings like on the screenshot.
Setting Devices
Connect devices to the bus and give each device a unique ID code. The ID code is later on used to send signals between iRidium driver and controlled devices.
Work in iRidium
1 Create a project.
2 Add Kleger Network driver, enter connection settings to the Waveshare RS485 to ETH adapter.
- Protocol - protocol (by default TCP);
- Host - IP-address of the converter;
- Port - connection port (by default 8998);
- Keep Alive - interval to check TCP connection;
3 Add devices connected to the bus and write ID Code of each device.
Devices
High power lamp control
Device to control light
| Command
|
Values
|
Description
|
| Scene 1-6 |
Value |
Turn on/turn off 1-6
|
| Lamp 1-4 |
Value |
Turn on/Turn off 1-4
|
| Feedbacks
|
Values
|
Description
|
| Scene 1-6 |
1- turned on,
0 - turned off |
Scene status 1-6
|
| Lamp 1-4 |
1- turned on,
0 - turned off |
Lamp status 1-4
|
Hotel Doorbell
Device to control room service
| Commands
|
Values
|
Description
|
| Do Not Disturb |
1- turn on,
0 - turn off. |
Turn on/turn off "Do Not Disturb".
|
| Clean Up |
1- turn on,
0 - turn off. |
Turn on/turn off "Clean Up".
|
| Please Wait |
1- turn on,
0 - turn off. |
Turn on/turn off "Please Wait".
|
| Make Up Room |
1- turn on,
0 - turn off. |
Turn on/turn off "Make Up Room".
|
| Please Repair |
1- turn on,
0 - turn off. |
Turn on/turn off "Please Repair".
|
Do Not Disturb and Clean Up buttons can't be active at the same time. This parameter is controlled by the internal logic of equipment.
| Feedbacks
|
Values
|
Description
|
| Do Not Disturb |
1- turned on,
0 - turned off. |
"Do Not Disturb" status.
|
| Clean Up |
1- turned on,
0 - turned off. |
"Clean Up" status.
|
| Please Wait |
1- turned on,
0 - turned off. |
"Please Wait" status.
|
| Make Up Room |
1- turned on,
0 - turned off. |
"Make Up Room" status.
|
| Please Repair |
1- turned on,
0 - turned off. |
"Please Repair" status.
|
Touch curtain type
Device to control blinds,shutters
| Commands
|
Values
|
Description
|
| Open |
Value |
Open blinds.
|
| Stop |
Value |
Stop blind movement.
|
| Close |
Value |
Close blinds.
|
| Feedbacks
|
Values
|
Description
|
| Open |
Value |
Open blinds.
|
| Stop |
Value |
Stop blind movement.
|
| Close |
Close blinds.
|
Touch dimming type
Device to dim light
| Commands
|
Values
|
Description
|
| Dimming |
0-100 |
Value for dimming
|
| Up |
Value |
Activation of the increase button.
|
| On/Off |
Value |
Turn on/off a dimmer.
|
| Down |
Value |
Activation of the decrease button.
|
| Key 1-6 |
1- turn on,
0 - turn off |
Turn on/off button 1-6.
|
When programming UP, DOWN buttons, enter the following values to send: value for Press - 1, value for Release - 0.
| Feedbacks
|
Values
|
Description
|
| Dimming |
0-100 |
Value of dimmer state.
|
| Up |
Value |
Status of the increase button.
|
| On/Off |
Value |
Status of the on/off button
|
| Down |
Value |
Status of the decrease button.
|
| Key 1-6 |
1- turned on,
0 - turned off. |
Turn on/ off button 1-6.
|
Touch light control type
Device to control light.
| Commands
|
Values
|
Description
|
| Master |
1- turn on,
0 - turn off. |
Turn on/off all lamps.
|
| Key 1-6 |
1- turn on,
0 - turn off. |
Turn on/off button 1-6.
|
| Feedbacks
|
Values
|
Description
|
| Master |
1- turned on,
0 - turned off |
Status of the "Master" button.
|
| Key 1-6 |
1- turned on,
0 - turned off |
Status of 1-6 button.
|
Fan coil unit (FCU to AC)
Thermostat panel
| Commands
|
Values
|
Description
|
| On/Off |
1- turn on,
0 - turn off. |
Turn on/off thermostat.
|
| SetTemperature |
10-39 С |
Set temperature value.
|
| Wind Speed |
1 - low,
2 - middle,
3 - high,
4 - auto |
Fan mode.
|
| A/C Mode |
0 - turn off,
1 - heat,
2 - cool,
3 - thermostatic,
4 - floor heating,
5 - fast heating,
6 - FAN, mode by default - cool |
Fancoil mode.
|
| Lock temperature |
1- turn on,
0 - turn off |
Blocking temperature control.
|
| Lock speed |
1- turn on,
0 - turn off |
Blocking fan control.
|
| Lock keyboard |
1- turn on,
0 - turn off |
Blocking the keyboard on the panel.
|
| Feedbacks
|
Values
|
Description
|
| Temperature |
0-100 |
Current temperature.
|
| SetTemperature |
10-39 С |
Set temperature.
|
| Wind Speed |
0 - device turned off,<bt />1 - low,
2 - middle,
3 - high,
4 - auto |
Fan mode
|
| A/C Mode |
0 - turn off,
1 - heat,
2 - cool,
3 - thermostatic,
4 - floor heating,
5 - fast heating,
6 - FAN, mode by default - cool |
Fancoil mode.
|
| Lock temperature |
1- turn on,
0 - turn off |
Status of blocking temperature control.
|
| Lock speed |
1- turn on,
0 - turn off |
Status of blocking fan control.
|
| Lock keyboard |
1- turn on,
0 - turn off |
Status of blocking the keyboard on a panel.
|
Setting Commands and Feedback Channels
To control equipment it is required to set commands (Commands) and feedback channels (Feedbacks). To send a command, drag'n'drop it on a graphic item and enter a value to send. To display feedback drag'n'drop a feedback channel on a graphic item and choose how to output or display a value.
Read more about work with graphic items in the
"Types of graphic items" article.
