Эта страница является переводом страницы TIS. Перевод выполнен на 100%.

---

iRidium for TIS

a set of tools to create control interfaces for equipment in the TIS.

The documentation was updated on 26.9.2023

Example: TIS

Connection

There are various ways of communicating with the bus, allowing you to work locally and over the Internet if you have a static IP address or a dynamic IP address:

Local Mode

The "Local" mode works only in the local network and it does not allow you to set up control of the bus via the Internet. A broadcast address is used for connection. Local connection works with any IP device by TIS.

TIS Remote Server

TIS Remote Server allows to connect to IP-gateway by TIS via internet in case you do not have a static IP-address or a domain (DDNS). Connection is set via the internet servers by TIS that are used for authorization between iRidium control panel and TIS IP-interface.

Serial

The Serial protocol supports connection via standard Serial port such as COM1 in Windows or /dev/ser1 in QNX. To work with the equipment, enter the «remote» host or a device with which the connection is performed.

Local Mode

The "Local" mode works only in the local network and it does not allow you to set up control of the bus via the Internet. A broadcast address is used for connection. Local connection works with any IP gateway by TIS.

If Fixed IP mode in turned on in the settings of TIS IP gateway, enter data to work in the local network

• IP Address - local IP-address of TIS module;
• Mask - subnet mask;
• Gateway - gateway by default.

Enter a local address to connect to TIS IP-gateway in the settings of the TIS Network driver. If it is recommended by the system admin, change the broadcast address, otherwise leave the setting by default.

• Connect type: Local – mode of local connection to TIS IP-module;
• Host – broadcasts address to exchange data with TIS;
• Port - connection port (by default it is 6000).

TIS Remote Server Mode

TIS Remote Server allows to connect to IP-gateway by TIS via internet in case you do not have a static IP-address or a domain (DDNS). Connection is set via the internet servers by TIS that are used for authorization between iRidium control panel and TIS IP-interface.

You can find addresses of available remote TIS servers in TIS DevSearch. Go to Network Configuration window and have a look at Server IP Address line. They can also be found in the settings of IP-interface.

Enter a required TIS server and its connections password in the IPPort Parameters section in the settings of the IP gateway. Hold the programming button on the device for 7 seconds. After it the device goes into the programming mode. Save the settings in the app and press a button on the device to leave the programming mode and reset the device.

Enter connection parameters to TIS IP gateway via a remote server in the settings of the TIS Network (UDP) driver;

• Host - address of a remote server TIS(Server IP Address). Enter the address of the TIS remote server that is set in the IP gateway;
• Port - port to connect to the IP gateway via a remote server. It's the same as in the settings of the IP gateway (by default it is 6000);
• Password - connection login from the settings of IP gateway;
• MAC - МАС-address of TIS IP gateway.

Serial

• Protocol - Serial;
• Log Level - level of logging;
• Used with iRidi device - set the host for the corresponding equipment (if this parameter is selected, the Host line will be inactive);
• Port - connection port.

Work in iRidium

1 Create a new project and add TIS Network driver.

2 Enter connection settings of a driver according to the type of connection Local or TIS Remote Server. You'll find detailed information about connection settings in the Connection setting section.

3 Click left mouse button on the added TIS Network driver and add required devices. Each device has a preset list of commands and feedback channels according to its type.

Fill in settings for each device to work:

• Subnet ID - subnet ID of the device;
• Device ID - device ID in the subnet;
• Device Type - type of device. Depending on the type of a device a definite list of "Operation Code" is available.

Setting Commands and Feedback Channels

To control equipment it is required to set commands (Commands) and feedback channels (Feedbacks). To send a command, drag'n'drop it on a graphic item and enter a value to send. To display feedback drag'n'drop a feedback channel on a graphic item and choose how to output or display a value.

Read more about work with graphic items in the "Types of graphic items" article.

In the TIS Network driver, each device has a set of Operation Codes specific to their type. Also, for the convenience of users, a Custom device has been added, where you can endow it with a unique set of Operation Code.

Air conditioner

Command:

Parameter	Value	Description
Use Timer	True, False.	An interval to send a command (sec.)
Operation Code	Read the temperature unit	It sends a request to get the temperature.
Value*	any value	It gets any value to activate a command.
Operation Code	Read air condition Fan speed and Mode En/Dis Flag	It sends a request to get the fan mode.
AC	1...n	The number of a thermostat.
Mode	Fan Auto, Fan High, Fan Med, Fan Low, Climate Cool, Climate Heat, Climate Fan, Climate Auto, Climate Dry.	The mode of thermostat work.
Value*	any value	It accepts any value to activate a command.
Operation Code	Read air condition temperature range	It sends a request to get the temperature range of a conditioner.
AC	1...n	The number of a thermostat.
Temperature parameter	Cool Low, Cool High, Heat Low, Heat High, Auto Low, Auto High, Dry Low, Dry High	A temperature mode.
Value*	any value	It accepts any value to activate a command.
Operation Code	Set the parameters of the air conditioner	It sets the parameters of conditioning.
AC	1...n	The number of a thermostat.
AC parameter	OnOff, Cool temperature, Mode, Speed, Heat temperature, Auto temperature, Dry temperature.	Parameters to control a thermostat.
Value *	0 - turn off, 1 - turn on	OnOff
	15-30	Cool temperature
	0-4 (Cool, Heat, Fan, Auto, Dry)	Mode
	0-3 (Auto, High, Med, Low)	Speed
	1...n	Room temperature
	15-35	Heat temperature
	0-4 (Cool, Heat, Fan, Auto, Dry)	Current mode
	0-3 (Auto, High, Med, Low)	Current speed
	15-35	Auto temperature
	15-35	Dry temperature
Operation Code	Read the parameters of the air condition	It sends a request to get the parameters of air-conditioning.
AC	1...n	The number of a thermostat.
AC parameter	OnOff, Cool temperature, Mode, Speed, Heat temperature, Auto temperature, Dry temperature.	Parameters to control a thermostat.
Value*	any value	It accepts any value to activate a command.
Operation Code	Set the parameters of thermostat	It sets the parameters of a thermostat.
Command	AC1, AC1 Cool temperature, AC1 Fan speed, AC1 Mode, AC1 Heat temperature, AC1 Auto temperature, Floor Heater, Floor temperature, Floor Heater 1, Floor Heater 2, Floor Heater all.	Selection of a parameter.
Value*	On, Off	AC1
	15 ~ 30	AC1 Cool temperature
	Auto, High, Med, Low	AC1 Fan speed
	Auto, Cool, Heat, Fan	AC1 Mode
	15 ~ 35	AC1 Heat temperature
	15 ~ 35	AC1 Auto temperature
	On, Off	Floor Heater
	15 ~ 35	Floor temperature
	On, Off, Temperature (15 ~ 35)	Floor Heater 1
	On, Off, Temperature (15 ~ 35)	Floor Heater 2
	On, Off, Temperature (15 ~ 35)	Floor Heater all
Operation Code	Read the parameters of thermostat	It sends a request to get parameters of a thermostat.
Action type	On/Off	It gets information about the state of a thermostat (on or off).
	Temperature	It gets the temperature of a thermostat
Value*	any value	It accepts any value to activate a command.

* - enter it when drag'n'dropping a command on a graphic item

Feedback:

Parameter	Value	Description
Operation Code	Read the temperature unit	The value of temperature.
Value *	n	Temperature.
Operation Code	Read air condition Fan speed and Mode En/Dis Flag	The value of a fan mode.
AC	1...n	The number of a conditioner.
Mode	Fan Auto, Fan Med, Fan Height, Fan Low, Climate Cool, Climate Heat, Climate Fan, Climate Auto, Climate Dry.	The mode of a conditioner.
Value *	0	Turned off.
	1	Turned on.
Operation Code	Read air condition temperature range	Temperature range.
AC	1...n	The number of a conditioner.
Temperature parameter	Cool Low, Cool High, Heat Low, Heat High, Auto Low, Auto High, Dry Low, Dry High.	Temperature parameter.
Value *	15-30	Cool Low
	15-30	Cool High
	15-35	Heat Low
	15-35	Heat High
	15-35	Auto Low
	15-35	Auto High
	15-35	Dry Low
	15-35	Dry High
Operation Code	Read the parameters of the air condition	Conditioner parameters.
AC	1...n	The number of a conditioner.
AC parameter	OnOff, Cool temperature, Mode, Speed, Room temperature, Heat temperature, Current mode, Current speed, Auto temperature, Dry temperature.	Parameters of a conditioner.
Value *	0 - turned off, 1 - turned on	OnOff
	15-30	Cool temperature
	0-4 (Cool, Heat, Fan, Auto, Dry)	Mode
	0-3 (Auto, High, Med, Low)	Speed
	1...n	Room temperature
	15-35	Heat temperature
	0-4 (Cool, Heat, Fan, Auto, Dry)	Current mode
	0-3 (Auto, High, Med, Low)	Current speed
	15-35	Auto temperature
	15-35	Dry temperature
Operation Code	Parameters of thermostat	Parameters of a thermostat.
Command	AC1, AC1 Cool temperature, AC1 Fan speed, AC1 Mode, AC1 Heat temperature, AC1 Auto temperature, Floor Heater, Floor temperature, Floor Heater 1, Floor Heater 2, Floor Heater all.	Selection of an air conditioner.
Value*	1 - On, 0 - Off	AC1
	15 ~ 30	AC1 Cool temperature
	0 ~ 3 (Auto, High, Med, Low)	AC1 Fan speed
	0 ~ 3 (Auto, Cool, Heat, Fan)	AC1 Mode
	15 ~ 35	AC1 Heat temperature
	15 ~ 35	AC1 Auto temperature
	1 - On, 0 - Off	Floor Heater
	15 ~ 35	Floor temperature
	1 - On, 0 - Off, Temperature (15 ~ 35)	Floor Heater 1
	1 - On, 0 - Off, Temperature (15 ~ 35)	Floor Heater 2
	1 - On, 0 - Off, Temperature (15 ~ 35)	Floor Heater all

* Value - a value that comes from equipment

Media Control

Command:

Parameter	Value	Description
Use Timer	True, False.	An interval to send a command (sec.)
Operation Code	Read audio source en/disable	It sends a request to get the status of the sound source (on / off).
Value*	any value	It accepts any value to activate a command.
Operation Code	Write audio Source en/disable	Turn on / off a sound source.
Value*	0	Turn off sound.
	1	Turn on sound.
Operation Code	Write radio station name	Write the name of a radio station.
Radio station id	0 - 25	The number of a radio station.
Value*	ASCII	It accepts a string to write a name.
Operation Code	Read radio station name	It sends a request to get the name of a radio station.
Value*	any value	It accepts any value to aсtivate a command.
Operation Code	Read how many album/song In SD/USB	It sends a request to get the number of albums / songs on a CD / USB.
Directory type	SD card, USB	The source of data.
Check type	Album, Track	The number of albums / tracks.
Value*	any value	It accepts any value to activate a command.
Operation Code	Audio command	It sends an audio command.
Control type	Music source, Playing mode, Album/radio control, Play control, Volume control	A type of control.
Music source	SD card, Audio in 1, FTP Server, FM Radio, Audio in 2.	Audio source.
Value*	any value	It accepts any value to activate a command.
Playing mode	After song stop, Repeat one song, Repeat one album, Repeat album, Randomize.	Play mode.
Value*	any value	It accepts any value to activate a command.
Album/radio control	Previous album, Next album, Specify album, Prev radio channel, Next radio channel, Specify radio no	Control of audion / albums.
Value*	any value	It accepts any value to activate a command.
Play control	Previous song, Next song, Play, Stop.	Control of playing.
Value*	any value	It accepts any value to activate a command.
Volume control	Volume, Treble, Bass	Sound setting: Decrase, Incrase, Vol value (only for the Volume parameter).
Value*	0 ~ 79	Volume
	-7 ~ 7	Treble
	-7 ~ 7	Bass

* - enter it when drag'n'dropping a command on a graphic item

Feedback:

Parameter	Value	Description
Operation Code	Audio sources en/dis	Audion source (on / off).
Input no	1...n	The number of an output.
Value*	0	Turned off.
	1	Turned on.
Operation Code	Radio station name	The name of a radio station.
Value*	ASCII	The name of a radio station.
Operation Code	Read How Many Album/Song In SD/USB	The number of albums/songs on a CD/USB.
Value*	0 ~100	The number of albums/songs on a CD/USB..
Operation Code	Audio command	Audio command (not realized).
Operation Code	Media control	Info about modes of player work.
Control type	Play/Stop/Pause, Mute, Source, Volume, Effect, Play mode, Channel change, Channel search, Album name, Song name, Play time total, Play time playing, Channel name, Channel frequence.	A type of command.
Value*	0 - Play, 1 - Stop, 2 - Pause.	Play/Stop/Pause.
	0 - Unmuted, 1 - Muted.	Mute.
	1 - SD, 2 - Audio Input 1, 4 - FM, 7 - Audio Input 2, 8 - USB	Source
	0 ~ 79	Volume
	1 - Normal, 2 - Pop, 3 - Classic, 4 - Jazz, 5 - Rock	Effect
	1 - After song stop, 2 - Repeat one song, 3 - Repeat one album, 4 - Repeat album, 5 - Randomize.	Play mode
	1 - Previous Channel, 2 - Next Channel	Channel change
	1...n	Channel search
	ASCII	Album name
	ASCII	Song name
	1...n	Play time total
	1...n	Play time playing
	ASCII	Channel name
	1...n	Channel frequence

* Value - a value that comes from equipment

Audio Matrix MTX-1Z-5S

Command:

Parameter	Value	Description
Use Timer	True, False.	An interval to send a command (sec.)
Operation Code	Read audio source en/disable	It sends a request to get the status of a sound source (on / off).
Value*	any value	It accepts any value to activate a command.
Operation Code	Write audio Source en/disable	Turn on/ off a sound source.
Value*	0	Turn off sound.
	1	Turn on sound.
Operation Code	Write radio station name	Write the name of a radio station.
Radio station id	0 - 25	The number of a radio station.
Value*	ASCII	It accepts a string to write the name of a radio station.
Operation Code	Read radio station name	It sends a request to get the name of a radio station.
Value*	any value	It accepts any value to activate a command.
Operation Code	Read how many album/song In SD/USB	It sends a request to get the number ot albums / songs on a CD / USB.
Directory type	SD card, USB	The source of data.
Check type	Album, Track	The number of albums / tracks.
Value*	any value	It accepts any value to activate a command.
Operation Code	Audio command	It sends an audio command.
Control type	Music source, Playing mode, Album/radio control, Play control, Volume control	A type of control.
Music source	SD card, Audio in 1, FTP Server, FM Radio, Audio in 2.	An audio source.
Value*	any value	It accepts any value to activate a command.
Playing mode	After song stop, Repeat one song, Repeat one album, Repeat album, Randomize.	A mode of playing.
Value*	any value	It accepts any value to activate a command.
Album/radio control	Previous album, Next album, Specify album, Prev radio channel, Next radio channel, Specify radio no	Control of radio / albums.
Value*	any value	It accepts any value to activate a command.
Play control	Previous song, Next song, Play, Stop.	Control of playing.
Value*	any value	It accepts any value to activate a command.
Volume control	Volume, Treble, Bass	Sound setting: Decrease, Increase, Vol value (only for the Volume parameter).
Value*	0 ~ 79	Volume
	-7 ~ 7	Treble
	-7 ~ 7	Bass

* - enter it when drag'n'dropping a command on a graphic item

Feedback:

Parameter	Value	Description
Operation Code	Audio sources en/dis	Audio source (on / off).
Value*	0	Turned off.
	1	Turned on.
Operation Code	Radio station name	The name of a radio station.
Value*	ASCII	The name of a radio station.
Operation Code	Read How Many Album/Song In SD/USB	The number of albums/songs on a CD/USB.
Value*	0 ~100	The number of albums/songs on a CD/USB.
Operation Code	Audio command	An audio command (not realized).
Operation Code	Media control	Data about the modes of player work.
Control type	Play/Stop/Pause, Mute, Source, Volume, Effect, Play mode, Channel change, Channel search, Album name, Song name, Play time total, Play time playing, Channel name, Channel frequence.	A type of commad.
Value*	0 - Play, 1 - Stop, 2 - Pause.	Play/Stop/Pause.
	0 - Unmuted, 1 - Muted.	Mute.
	1 - SD, 2 - Audio Input 1, 4 - FM, 7 - Audio Input 2, 8 - USB	Source
	0 ~ 79	Volume
	1 - Normal, 2 - Pop, 3 - Classic, 4 - Jazz, 5 - Rock	Effect
	1 - After song stop, 2 - Repeat one song, 3 - Repeat one album, 4 - Repeat album, 5 - Randomize.	Play mode
	1 - Previous Channel, 2 - Next Channel	Channel change
	1...n	Channel search
	ASCII	Album name
	ASCII	Song name
	1...n	Play time total
	1...n	Play time playing
	ASCII	Channel name
	1...n	Channel frequence

* Value - a value that comes from equipment

Thermostat

Command:

Parameter	Value	Description
Use Timer	True, False.	An interval to send a command (sec.)
Operation Code	Read the temperature unit	It sends a request to get the current temperature.
Value*	any value	It accepts any value to activate a command.
Operation Code	Read air condition Fan speed and Mode En/Dis Flag	It sends a request ot get the fan mode.
AC	1...n	The number of a thermostat.
Mode	Fan Auto, Fan High, Fan Med, Fan Low, Climate Cool, Climate Heat, Climate Fan, Climate Auto, Climate Dry.	Work modes of a thermostat.
Value*	any value	It accepts any value to activate a command.
Operation Code	Read air condition temperature range	It sends a request to get the temperature range of a conditiner.
AC	1...n	The number of a thermostat.
Temperature parameter	Cool Low, Cool High, Heat Low, Heat High, Auto Low, Auto High, Dry Low, Dry High	A temperature mode.
Value*	any value	It accepts any value to activate a command.
Operation Code	Set the parameters of the air condition	It sets parameters of air conditioning.
AC	1...n	The number of a thermostat.
AC parameter	OnOff, Cool temperature, Mode, Speed, Heat temperature, Auto temperature, Dry temperature.	Parameters to control a thermostat.
Value *	0 - turn off, 1 - turn on	OnOff
	15-30	Cool temperature
	0-4 (Cool, Heat, Fan, Auto, Dry)	Mode
	0-3 (Auto, High, Med, Low)	Speed
	1...n	Room temperature
	15-35	Heat temperature
	0-4 (Cool, Heat, Fan, Auto, Dry)	Current mode
	0-3 (Auto, High, Med, Low)	Current speed
	15-35	Auto temperature
	15-35	Dry temperature
Operation Code	Read the parameters of the air condition	It sends a request to get the parameters of conditioning.
AC	1...n	The number of a thermostat.
AC parameter	OnOff, Cool temperature, Mode, Speed, Heat temperature, Auto temperature, Dry temperature.	Parameters to control a thermostat.
Value*	any value	It accepts any value to activate a command.
Operation Code	Set the parameters of thermostat	It sets parameters of a thermostat.
Command	AC1, AC1 Cool temperature, AC1 Fan speed, AC1 Mode, AC1 Heat temperature, AC1 Auto temperature, Floor Heater, Floor temperature, Floor Heater 1, Floor Heater 2, Floor Heater all.	Selection of a parameter.
Value*	On, Off	AC1
	15 ~ 30	AC1 Cool temperature
	Auto, High, Med, Low	AC1 Fan speed
	Auto, Cool, Heat, Fan	AC1 Mode
	15 ~ 35	AC1 Heat temperature
	15 ~ 35	AC1 Auto temperature
	On, Off	Floor Heater
	15 ~ 35	Floor temperature
	On, Off, Temperature (15 ~ 35)	Floor Heater 1
	On, Off, Temperature (15 ~ 35)	Floor Heater 2
	On, Off, Temperature (15 ~ 35)	Floor Heater all
Operation Code	Read the parameters of thermostat	It sends a request to get parameters of a thermostat.
Action type	On/Off	It gets data about the state of a thermostat (on / off).
	Temperature	It gets the temperature of a thermostat.
Value*	any value	It accepts any value to actiavate a command.

* - enter it when drag'n'dropping a command on a graphic item

Feedback:

Parameter	Value	Description
Operation Code	Read the temperature unit	Temperature value.
Value *	n	Temperature.
Operation Code	Read air conditioner Fan speed and Mode En/Dis Flag	The value of a fan mode.
AC	1...n	The number of a conditioner.
Mode	Fan Auto, Fan Med, Fan Height, Fan Low, Climate Cool, Climate Heat, Climate Fan, Climate Auto, Climate Dry.	The mode of an air conditioner.
Value *	0	Turned off.
	1	Turned on.
Operation Code	Read air conditioner temperature range	A temperature range.
AC	1...n	The number of an air conditioner.
Temperature parameter	Cool Low, Cool High, Heat Low, Heat High, Auto Low, Auto High, Dry Low, Dry High.	Temperature parameter.
Value *	15-30	Cool Low
	15-30	Cool High
	15-35	Heat Low
	15-35	Heat High
	15-35	Auto Low
	15-35	Auto High
	15-35	Dry Low
	15-35	Dry High
Operation Code	Read the parameters of the air condition	Conditioner parameters.
AC	1...n	The number of a conditioner.
AC parameter	OnOff, Cool temperature, Mode, Speed, Room temperature, Heat temperature, Current mode, Current speed, Auto temperature, Dry temperature.	Parameters of a conditioners.
Value *	0 - turned off, 1 - turned on	OnOff
	15-30	Cool temperature
	0-4 (Cool, Heat, Fan, Auto, Dry)	Mode
	0-3 (Auto, High, Med, Low)	Speed
	1...n	Room temperature
	15-35	Heat temperature
	0-4 (Cool, Heat, Fan, Auto, Dry)	Current mode
	0-3 (Auto, High, Med, Low)	Current speed
	15-35	Auto temperature
	15-35	Dry temperature
Operation Code	Parameters of thermostat	Themostat parameters.
Command	AC1, AC1 Cool temperature, AC1 Fan speed, AC1 Mode, AC1 Heat temperature, AC1 Auto temperature, Floor Heater, Floor temperature, Floor Heater 1, Floor Heater 2, Floor Heater all.	Selection of a parameter.
Value*	1 - On, 0 - Off	AC1
	15 ~ 30	AC1 Cool temperature
	0 ~ 3 (Auto, High, Med, Low)	AC1 Fan speed
	0 ~ 3 (Auto, Cool, Heat, Fan)	AC1 Mode
	15 ~ 35	AC1 Heat temperature
	15 ~ 35	AC1 Auto temperature
	1 - On, 0 - Off	Floor Heater
	15 ~ 35	Floor temperature
	1 - On, 0 - Off, Temperature (15 ~ 35)	Floor Heater 1
	1 - On, 0 - Off, Temperature (15 ~ 35)	Floor Heater 2
	1 - On, 0 - Off, Temperature (15 ~ 35)	Floor Heater all

* Value - a value that comes from equipment

Energy

Command:

Parameter	Value	Description
Use Timer	True, False.	An interval to send a command (sec.)
Operation Code	Energy meter data request	It requests data from an electricity meter.
Energy type	Basic, Energy metter data request, This month, (1~12) month energy total	A type of request.
Value (Energy metter data request)	Import active, Export active, Import reactive, Export reactive, Total active, Total reactive.	A type of meter data.
Value (Basic)	Line to neutral, Current, Active power, Apparent power, Reactive power, Power factor, Phase angle, Frequency.	A type of meter data.
Value*	any value	It accepts any value to activate a command.

* - enter it when drag'n'dropping a command on a graphic item

Feedback:

Parameter	Value	Description
Operation Code	Energy meter data request	It requests data from an electricity meter.
Energy type	Basic, Energy metter data request, This month, (1~12) month energy total	A type of request.
Value (Energy meter data request)	Import active, Export active, Import reactive, Export reactive, Total active, Total reactive.	A type of meter data.
Value (Basic)	Line to neutral, Current, Active power, Apparent power, Reactive power, Power factor, Phase angle, Frequency.	A type of meter data.
Value*	n	Data from an electricity meter.

* Value - a value that comes from equipment

Weather

Command:

Parameter	Value	Description
Use Timer	True, False.	An interval to send a command (sec.)
Operation Code	Read weather status	It requests weather data
Value*	any value	It accepts any value to activate a command.

* - enter it when drag'n'dropping a command on a graphic item

Feedback:

Parameter	Value	Description
Operation Code	Read weather status	It requests data from an electricity meter.
Temperature parameter	Wind direction, Temperature, Humidity, Wind speed, Gust speed, Rain fall, Lighting intencity, Ultraviolet index, Low battery status, Date time.	A type of data.
Value*	1-North, 2-North East, 4-East, 8-South East, 16-South, 32-South West, 64-West, 128-North East.	Wind direction.
	0 ~ 100 %	Humidity.
	Value	Wind speed.
	Value	Gust speed.
	0 - no rain, 1 - rain.	Rain fall.
	Value	Lighting intencity.
	0 ~ 15	Ultraviolet index.
	0 - normal, 1 - low.	Low battery status.
	date/time on a device.	Date time.

* Value - a value that comes from equipment

Logic 4T sensor / Logic Health sensor / Logic PIR sensor / Logic 10F sensor

Command:

Parameter	Value	Description
Use Timer	True, False.	An interval to send a command (sec.)
Operation Code	Read logic status	It sends a request to get the status of a device.
Logic ID	1 ~ n	Device ID.
Value*	any value	It accepts any value to activate a command.

* - enter it when drag'n'dropping a command on a graphic item

Feedback:

Parameter	Value	Description
Operation Code	Read 10F logic status	It gets the logic status of 10F.
Logic ID	1 ~ n	device ID.
Logic sensor parameter	Logic delay time, Lux, PIR status, Relay status, Digital input 1-2, FLag A, FLag A status, FLag B, FLag B status, Temperature, Date time, Week.	Parameters of a logic sensor.
Value*	n	Parameter value of a logic sensor.
Operation Code	Read 4T logic status	It gets the 4T logic status.
Logic ID	1 ~ n	Device ID.
Value*	n	Parameter value of a logic sensor.
Operation Code	Read PIR logic status	It gets the PIR logic status.
Logic ID	1 ~ n	Device ID.
Logic sensor parameter	Logic delay time, Lux, PIR status, Relay status 1-2, FLag A, FLag A status, FLag B, FLag B status, Date time.	Parameters of a logic sensor.
Value*	n	Parameter value of a logic sensor.
Operation Code	Read Health logic status	It gets the Health logic status.
Logic ID	1 ~ n	Device ID.
Logic sensor parameter	Logic delay time, Lux, Noise, Eco, TVOC, Temperature, Humidity, Digital input 1-3, PIR status, FLag A, FLag A status, FLag B, FLag B status, Date time, CO, Eco level, TVOC level, CO level.	Parameters of a logic sensor.
Value*	n	Parameter value of a logic sensor.

* Value - a value that comes from equipment

Digital Input

Command:

Parameter	Value	Description
Use Timer	True, False.	An interval to send a command (sec.)
Operation Code	Read Status from 10FEnergy Servant Sensor	It requests the status of the10FEnergy Servant sensor.
Value*	any value	It accepts any value to activate a command.
Operation Code	Read status from other digital inputs	It requests the status pf other digital inputs.
Value*	any value	It accepts any value to activate a command.

* - enter it when drag'n'dropping a command on a graphic item

Feedback:

Parameter	Value	Description
Operation Code	Read Status from 10FEnergy Servant Sensor	It reads the status from the 10FEnergy Servant sensor.
Servant sensor parameter	Dry contact 1/2, Lux type, Motion sensor, FLAG A/B, Delay time, Lux Value, Type dry contact 1/2.	Sensor parameters.
Value*	1 - Closed, 0 - Open.	Dry contact 1/2
	ASCII	Lux type
	0 - No motion, 1 - Motion	Motion sensor
	0 - Invalid, 1 - Turn off, 2 - Turn on.	FLAG A/B
	0...n	Delay time
	1 - Within the range, 0 - Outside the range	Lux Value
	ASCII	Type dry contact 1/2
Operation Code	Read status from other digital inputs	It reads the status of other digital inputs.
Input no	1...n	The number of an input.
Value*	1 - Opened, 0 - Closed.	The status of a dry contact.

* Value - a value that comes from equipment

Floor Heating

Command:

Parameter	Value	Description
Use Timer	True / False.	An interval to send a commad (sec.)
Operation Code	Read the state of floorheating	It requests the state of the warm floor.
Id	FH 1 / FH 2	Id of the warm floor.
Value*	any value	It accepts any value to activate a command.
Operation Code	Read the limits of floorheating	It requests the heating limit of the warm floor.
Id	FH 1 / FH 2	Id of the warm floor.
Value*	any value	It accepts any value to activate a command.
Operation Code	Controll floorheating	Control of floor heating.
Id	FH 1 / FH 2	Id of the warm floor.
Command	Low limit, High limit, Enabled, Mode	Commands of the warm floor.
Value*	any value	Low limit
	any value	High limit
	0 - Turn off, 1 - Turn ob	Enabled
	0 ~ n	Mode
Operation Code	Set the parameters of thermostat	Set heating parameters.
Command	AC1, AC1 Cool temperature, AC1 Fan speed, AC1 Mode, AC1 Heat temperature, AC1 Auto temperature, Floor Heater, Floor temperature, Floor Heater 1/2, Floor Heater all.	Commands of the warm floor.
Value*	1 - On, 0 - Off	AC1
	15 ~ 30	AC1 Cool temperature
	0 ~ 3 (Auto, High, Med, Low)	AC1 Fan speed
	0 ~ 2 (Auto, Cool, Heat)	AC1 Mode
	15 ~ 35	AC1 Heat temperature
	15 ~ 35	AC1 Auto temperature
	1 - On, 0 - Off	Floor Heater
	15 ~ 35	Floor temperature
	1 - On, 0 - Off, Temperature (15 ~ 35)	Floor Heater 1/2
	1 - On, 0 - Off, Temperature (15 ~ 35)	Floor Heater all
Operation Code	Read the parameters of thermostat	It requests thermostat parameters.
Value*	any value	It accepts any value to activate a command.

* - enter it when drag'n'dropping a command on a graphic item

Feedback:

Parameter	Value	Description
Operation Code	State of floorheating	The state of floor heating.
Id	FH 1 / FH 2	ID of floor heating.
Command	Room temp, State	A tracked parameter.
Value*	0 ~ n	Room temp
	1 - Turned on, 0 - Turned off.	State
Operation Code	Limits of floorheating	The limits of floor heating.
Id	FH 1 / FH 2	ID of floor heating.
Command	Low limit, High limit, Enabled, Mode	The parameter of limits.
Value*	any value	Low limit
	any value	High limit
	0 - Turned off, 1 - Turned on	Enabled
	0 ~ n	Mode
Operation Code	Parameters of thermostat	Thermostat parameters.
Command	AC1, AC1 Cool temperature, AC1 Fan speed, AC1 Mode, AC1 Heat temperature, AC1 Auto temperature, Floor Heater, Floor temperature, Floor Heater 1/2, Floor Heater all.	Parameters of floor heating.
Value*	1 - On, 0 - Off	AC1
	15 ~ 30	AC1 Cool temperature
	0 ~ 3 (Auto, High, Med, Low)	AC1 Fan speed
	0 ~ 2 (Auto, Cool, Heat)	AC1 Mode
	15 ~ 35	AC1 Heat temperature
	15 ~ 35	AC1 Auto temperature
	1 - On, 0 - Off	Floor Heater
	15 ~ 35	Floor temperature
	1 - On, 0 - Off, Temperature (15 ~ 35)	Floor Heater 1/2
	1 - On, 0 - Off, Temperature (15 ~ 35)	Floor Heater all

* Value - a value that comes from equipment

10F Energy Servant

Command:

Parameter	Value	Description
Use Timer	True, False.	An interval to send a command (sec.)
Operation Code	Read status from 10FEnergy Servant Sensor	It requests the status if the 10FEnergy Servant sensor.
Value*	any value	It accepts any value to activate a command.
Operation Code	Read status from other digital inputs	It requests the status of other digital inputs.
Value*	any value	It accepts any value to activate a command.

* - enter it when drag'n'dropping a command on a graphic item

Feedback:

Parameter	Value	Description
Operation Code	Read status from 10FEnergy Servant Sensor	It requests the status of the 10FEnergy Servant sensor
Servant sensor parameter	Dry contact 1/2, Lux type, Motion sensor, FLAG A/B, Delay time, Lux Value, Type dry contact 1/2.	Sensor parameter
Value*	Open = 1, Close = 0	Dry contact 1/2
	0 ~ n	Lux type
	No Movement =0, Movement=1	Motion sensor
	Invalid=0, OFF=1, ON=2	FLAG A/B
	0 ~ n (sec)	Delay time
	In brightness range=1, Beyond the brightness range=0	Lux Value
	0 ~ n	Type dry contact 1/2
Operation Code	Read status from other digital inputs	It requests the status of other diigtal inputs
Input no	0 ~n	The number of an input.
Value*	NC=1, NO=0, Invalid=2	Type of dry contact 1/2/3/4
	Open =1, Close =0.	Status of dry contact 1/2/3/4

* Value - a value that comes from equipment

Security Module

Command:

Parameter	Value	Description
Use Timer	True, False.	An interval to send a command (sec.)
Operation Code	Arm/Disarm Security	Activation / deactivation of security devices.
Zone no	0...n	The number of a zone.
Command	Vacation, Away, Night, Night with visitor, Day, Disarm.	A work mode of devices.
Value*	any value	It accepts any value to activate a command.

* - enter it when drag'n'dropping a command on a graphic item

Feedback:

Parameter	Value	Description
Operation Code	Arm/Disarm Security	The status of security devices.
Zone no	0...n	The number of a zone.
Value*	1	Vacation
	2	Away
	3	Night
	4	Night with visitor
	5	Day
	6	Disarm

* Value - a value that comes from equipment

Universal Switch Project \ Universal Switch DVD \ Universal Switch IPTV \ Universal Switch TV Box \ Universal Switch TV

Command:

Parameter	Value	Description
Use Timer	True, False.	An interval to send a command (sec.) .
Operation Code	Universal switch	Activation of a universal switch.
Switch no	0...n	The number of a switch.
Control type	ON \ Off.	Turn on \ off
Value*	any value	It accepts any value to activate a command.

* - enter it when drag'n'dropping a command on a graphic item

Universal Switch

Command:

Parameter	Value	Description
Use Timer	True, False.	An interval to send a command (sec.) .
Operation Code	Universal switch	Activation of a universal switch.
Switch no	0...n	The number of a switch.
Control type	ON \ Off.	Turn on \ off
Value*	any value	It accepts any value to activate a command.

* - enter it when drag'n'dropping a command on a graphic item

Feedback:

Parameter	Value	Description
Operation Code	Universal switch	The state of a universal switch
Switch no	0...n	The number of a switch.
Value*	1	ON
	0	Off

* Value - a value that comes from equipment

Curtain Motor

Command:

Parameter	Value	Description
Use Timer	True, False.	An interval to send a command (sec.)
Operation Code	Read status of curtain	It sends a request to get the status of the curtain position.
Value*	any value	It accepts any value to activate a command.
Operation Code	Curtain сontrol	Activation of a universal switch.
Switch no	0...n	The number of a switch.
Control type	Stop, Open, Close.	Stop, Open, Close.
Value*	any value	It accepts any value to activate a command.

* - enter it when drag'n'dropping a command on a graphic item

Feedback:

Parameter	Value	Description
Operation Code	Curtain control	It gets the status of the curtain position.
Switch no	0...n	The number of a switch.
Value*	0	Stop
	1	Open
	2	Close

* Value - a value that comes from equipment

Tubular Motor

Command:

Parameter	Value	Description
Use Timer	True, False.	An interval to send a command (sec.)
Operation Code	Single channel control	One-channel control.
Channel no	1~255 (255 is sent to all channels of a device)	The number of a channel.
Brightness level	0~100	The level of brightness (in per cent).
Dim/ramp time	0~3600 (сек.)	The time of activation.
Value*	any value	It accepts any value to activate a command.
Operation Code	Read status of channels	It gets the staus of channels.
Value*	any value	It accepts any value to activate a command.
Operation Code	Curtain сontrol	Control of curtains.
Switch no	0...n	The number of a switch.
Control type	Stop, Open, Close.	A type of control.
Value*	any value	It accepts any value to activate a command.
Operation Code	Read status of curtain	It gest the status of the curtain position.
Value*	any value	It accepts any value to activate a command.

* - enter it when drag'n'dropping a command on a graphic item

Feedback:

Parameter	Value	Description
Operation Code	Single channel control	It gets the status of channels.
Channel no	0...n	The number of a channel.
Value*	0~100	A value in the channel
Operation Code	Curtain control	It gest the status of the curtain position.
Switch no	0...n	The number of a channel.
Value*	0	Stop
	1	Open
	2	Close

* Value - a value that comes from equipment

RGB \ Dimmer \ Relay

Command:

Parameter	Value	Description
Use Timer	True, False.	An interval to send a command (sec.)
Operation Code	Scene control	Control of scenes.
Area no	0~254	The number of an area / control zone.
Scene no	0~254	The number of a scene (if the value is 0, the number of the scene will be taken from the Value*)
Value*	any value	It accepts any value to activate a command.
Operation Code	Single channel control	One-channel control
Channel no	1~255 (255 - it is sent to all channels of a device)	The number of a channel.
Brightness level	0~100	The brightness level of a selected channel (if the value is 0, the brightness level will be taken from the Value*).
Dim/ramp time	0~3600 (sec.)	Time of activation.
Value*	any value	It accepts any value to activate a command.
Operation Code	Read status of channels	It requests the status of channels.
Value*	any value	It accepts any value to activate a command.
Operation Code	Sequence Control	It turns on a sequence of scenes.
Area no	0~254	The number of an area / a control zone.
Sequence no	0~254	The number of a sequence (if the value is, the number of the sequence will be taken from the Value*).
Value*	any value	It accepts any value to activate a command.

* - enter it when drag'n'dropping a command on a graphic item

Feedback:

Parameter	Value	Description
Operation Code	Scene control	It gets the state of channels in a scene.
Area no	0~254	The number of an area / a control zone.
Value*	0~254 (254 - manuel control, scenes are turned off)	The current scene (a sequence number).
Operation Code	Single channel control	It gets the state of a channel.
Channel no	1~255 (255 - it is sent to all channels of a device)	The number of a channel.
Value*	0~100	The current value of a channel.
Operation Code	Sequence control set status	The status of a set of sequence of scenes.
Area no	0~254	The number of an area / a control zone.
Value*	0~254	The current status.

* Value - a value that comes from equipment